manualshive.com logo in svg

Lightware 91540021, User Manual

Share
Download
Lightware 91540021 User Manual Download Page 19

 

3. Product Overview 

HDMI-TPS-RX110AY series – User's Manual 

19

Appliedfirmwarepackage:v1.4.0 | LDCsoftware:v2.4.0b3

3.3. 

Front Panel - Special Functions

3.3.1. 

Programmable Function Button

Action or an operation can be assigned to the 

Function

button.“Functionbuttonpressed”isaconditionthat

can be selected in the Event Manager. See more details in the 

Event Manager

 section. 

#function

3.3.2. 

Enable Dynamic (DHCP) IP Address

ThedevicegetsastaticIPaddressasafactorydefaultsetting.Ifthissettingdoesnotfittothecircumstances

duringinstallorusage,DHCPcanbeenabledfromthefrontpanel:

Step 1. 

Make sure the device is powered on and operational.

Step 2. 

Press and keep pressed the 

Function

 button for 5 seconds.

Step 3. 

After5secondsfrontpanelLEDsstartblinking;releasethebuttonandpressit3timesagainquickly

(within 3 seconds).

Step 4. 

TheLEDsgetdark,DHCPgetsenabled.

#dhcp

3.3.3. 

Reset to Factory Default Settings

Torestorefactorydefaultvalues,dothefollowingsteps:

Step 1. 

Make sure the device is powered on and operational.

Step 2. 

Press and keep pressed the 

Function

buttonfor10seconds.After5secondsfrontpanelLEDsstart

blinking but keep on pressing the button.

Step 3. 

After 10 seconds the blinking gets faster; release the button and press it 3 times again quickly (within 

3 seconds).

Step 4. 

TheLEDsgetdark,thedevicerestoresthefactorydefaultsettingsandreboots.

Factory default settings are listed in the 

Factory Default Settings

 section. 

#factory

3.3.4. 

Reseting the Device

Infewcases(afterfirmwareupgrade,etc)youmayneedtoresetthedevice.Pushingtheresetbuttonresults

the same as you disconnect and reconnect the power adaptor to the receiver. To reseting the device follow 

thesteps:

Step 1. 

Push the button with a thin object for a second.

Step 2. 

Waituntilthedevicereboots.YoucanusethereceiverwhentheLIVELEDisblinkingslowlyagain.

ATTENTION! 

Reseting the device does not reset the settings to factory defaults. To reset factory default 

settings see previous section.

#reset #restart #reboot

3.3.5. 

Entering Bootload Mode

Itmayhappenthatthefirmwareupgradeprocessisnotsuccessfulasthedevicecannotbeswitchedto

bootload mode automatically. In this case, receiver device can be forced to switch to bootload mode as 

follows:

Step 1. 

Make sure the transmitter is powered off.

Step 2. 

Press and keep pressed the 

Function

 button.

Step 3. 

Poweronthereceiver.IfthedeviceisswitchedtobootloadmodetheLIVELEDisblinkingquickly

(lessthan500msdutycycle).TheotherLEDsareoff.

#bootload

 

Summary of Contents for 91540021
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands