manualshive.com logo in svg

Lightware 91540021, User Manual, Page: 110 / 119

Share
Download
Lightware 91540021 User Manual Download Page 110

 

11. Appendix 

HDMI-TPS-RX110AY series – User's Manual 

110

Appliedfirmwarepackage:v1.4.0 | LDCsoftware:v2.4.0b3

11.1. Specification

General

Compliance ......................................................................................................................................................CE
EMC compliance (emission) ..............................................................................................

IEC/EN55032:2015

EMC compliance (immunity) ..............................................................................................

IEC/EN55024:2011

Warranty

 ................................................................................................................................................... 3 years

Cooling..................................................................................................................................................... Passive
Operating temperature ............................................................................................

0to+50˚C(+32to+122˚F)

Operating humidity ..............................................................................................

10%to90%,non-condensing

Power

Power supply ........................................................................External power adaptor or PoE remote powering
Power adaptor ..............................................................................

In100-240VAC50/60Hz,Out12VDC,2A

Power connector .......................................................................................

LockingDCconnector(2.1mmpin)

Power over TPS .........................................................................................................

DC48V,1A(IEEE802.3af)

Power consumption ............................................................................................................................

10W(typ)

Enclosure

Rack mountable ............................................................................................................................................. Yes
Material .............................................................................................................................................. 1 mm steel
Dimensions in mm ...........................................................................................................

221Wx100.4Dx26H

Dimensions in inch .......................................................................................................

8.7Wx3.95Dx1.02H

Weight

 ..........................................................................................................................................................607 g

Audio/Video Ports

HDCP compliant...........................................................................................................................

Yes,HDCP1.4

TPS Input Port

TPS port connector type............................................................................................................

RJ45connector

Power over Ethernet (PoE) ................................................................................................... Yes (IEEE 802.3af)
Compliance ....................................................................................................................................... HDBaseT

TM

Transferred signals (TPS) ..................................................................

Video,Audio,RS-232,Infrared,Ethernet

Max. video resolutions ...........................................................................................

1920x1080@120Hz,24bit

 ...................................................................................................................................1600x1200@60 Hz, 36 bit
 ...................................................................................................................................

3840x2160@30Hz,24bit

Audio formats .............................................................................................................................8 channel PCM
 ....................................................................................................................................................... Dolby TrueHD
 ................................................................................................................................... DTS-HD Master Audio 7.1
Reclocking .................................................................................................................Pixel Accurate Reclocking
HDCP compliant............................................................................................................................................. Yes

HDMI Output Port

HDMI port connector type ............................................................................. 19-pole HDMI Type A receptacle
Standard ..................................................................................................................................

DVI1.0,HDMI1.4

Max. video resolutions ...........................................................................................

1920x1080@120Hz,24bit

 ...................................................................................................................................1600x1200@60 Hz, 36 bit
 ...................................................................................................................................

3840x2160@30Hz,24bit

Audio formats .............................................................................................................................8 channel PCM
 ....................................................................................................................................................... Dolby TrueHD
 ................................................................................................................................... DTS-HD Master Audio 7.1
Reclocking .................................................................................................................Pixel Accurate Reclocking
HDCP compliant............................................................................................................................................. Yes

Analog Audio Output Port

Audio port connector ................................................................................................ 5-pole Phoenix connector
Signal transmission ....................................................................................... Balanced and unbalanced audio

Volume

............................................................................................................................................-95.62 – 0 dB

Control Ports

RS-232 Control

Serial port connector ................................................................................................ 3-pole Phoenix connector
Available Baud rates ...............................................................................................

between4800and115200

Available Data bits ......................................................................................................................................8 or 9
Available Parity......................................................................................................................

None/Odd/Even

Available Stop bits ...............................................................................................................................

1/1.5/2

USB Control

USB connector ...........................................................................................................................USB mini B type
USB 2.0 compliance....................................................................................................................................... Yes

 

Summary of Contents for 91540021
























































































































Reviews:

No comments