LightPointe AireLink 60 Installation And User Manual Download Page 87

Page: 87 / 133

AireLink



60 Installation and User Manual Rev. D

LinkManager™– Network Management

Platform

Page 87

SFP Data Port:

Figure 6-7: Port Status View (SFP Data Port)

SFP DATA PORT

Status

Displays Link Status



Connected / Disconnected

Link

Displays Link Status



UP/DOWN

Activity

Displays Link Activity



Traffic / No Traffic

Enable

Port Status



ENABLED / DISABLED

Part Number

Displays SFP Part Number

Transceiver

Displays SFP Transceiver Information

Temperature

Shows SFP Temperature

TX Power

Displays SFP TX Transmission Power

RX Power

Displays SFP RX Receive Power Level

Flow Control

Control Flow



ENABLED/DISABLED

Summary of Contents for AireLink 60






































































































































Search results

Summary of Contents for AireLink 60

Reviews:

Related manuals for AireLink 60

Brands by name

Popular brands

LightPointe AireLink 60, Installation And User Manual

Search results

Summary of Contents for AireLink 60

Reviews:

Related manuals for AireLink 60

Brands by name

Popular brands