631 Airport Road, Fall River, MA 02720
COMPANY
A
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING LUMINAIRE
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
IS:404S36
INSTRUCTION SHEET NO.
B0204
Page 1
Note: This instruction sheet covers several luminaire styles.
Powerhead assembly, lamp type, and reflector style may vary
slightly from that shown, although installation is the same.
INSTRUCTION SHEET FOR ASSEMBLY AND INSTALLATION
OF 9”,12”&16” PENDALYTE™ SERIES WITH STEM
1.
Using pipe cutting tool, shorten STEM to
appropriate length. Clean all burrs and sharp
edges from cut end of Stem.
2.
Position DRILL LOCATOR over cut end of
STEM (Fig. 2). Gently tap down on DRILL
LOCATOR until fully seated on end of STEM.
3.
Position CENTER PUNCH into bottom SLOT
in DRILL LOCATOR and mark a small dimple
in STEM (Fig. 3).
4.
Align 1/8" DRILL BIT (local hardware item)
into bottom slot of DRILL LOCATOR so tip of
DRILL BIT rests in dimple (Fig. 4).
5.
Drill hole completely through STEM allowing
DRILL LOCATOR to guide DRILL BIT. Do
not force DRILL BIT. It is recommended to
hold DRILL LOCATOR securely in a vise or
other device prior to drilling hole.
Instructions for shortening stem
ATTENTION: Cut end with smaller diameter holes only.
(Fig.1)
CAUTION:
Eye protection should always be worn when using hand and
power tools during the assembly procedure outlined below.
1.
Assemble STEM to BALL ALIGNER using SET SCREWS. SET SCREWS
should align with small holes near end of stem. Pull wires through BALL
ALIGNER leaving no less than 6” exposed. (Fig 1)
2.
Strip back insulation on Black, White and Green wires 3/8” at both ends.
3.
Attach MOUNT PLATE to STEM by aligning holes as shown and inserting
PIN. Secure PIN with COTTER PIN.
4.
Wire POWERHEAD ASSEMBLY using WIRE NUTS (local hardware item):
black luminaire lead to hot (black) lead, white luminaire lead to neutral (white)
lead. Attach luminaire ground wire(s) (green and/or bare) to green ground
wire.
5.
Attach POWERHEAD to MOUNT PLATE with 8-32 SCREWS
6.
Install SWIVEL CROSSBAR onto outlet box using OUTLET BOX SCREWS.
7.
Insert STEM with BALL ALIGNER through CANOPY prior to wiring.
8.
Place BALL ALIGNER with STEM into CROSS BAR through side access hole.
When seated the BALL ALIGNER KEYWAY will line up with tab on
CROSSBAR. Push supply leads into outlet box.
9.
Slide SAFETY STRAP into position and secure with screw.
10. Make electrical connections: black lead to hot (black) supply lead; white lead
to neutral (white) supply lead. Green lead is ground wire and must be
connected to grounding terminal or ground lead inside outlet box. Use WIRE
NUTS (local hardware item).
Note: Refer to POWERHEAD instruction
sheet for detailed wiring information.
11. Place CANOPY over CROSSBAR lining up slots on CANOPY with RUBBER
CAPS on CROSSBAR turning clockwise until it locks into place.
NOTE: If custom length is required see below
STEM
8-32 SCREW
PIN
COTTER PIN
MOUNT PLATE
POWERHEAD
ASSEMBLY
BALL ALIGNER
SET SCREW
SAFETY
STRAP
W/SCREW
OUTLET
BOX
SCREW
CANOPY
SWIVEL
CROSSBAR
RUBBER
CAPS
KEYWAY
Fig 1
