Lightolier
a Genlyte company
www.lightolier.com
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
© 2007 Genlyte Group LLC • I0407
Job Information
Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
Lytecaster
®
Recessed Downlighting
1004IC
Page 1 of 1
5" Aperture
0
Incandescent Convertible IC/Non-IC Frame-In Kit
5" Aperture: Complete Fixture consists of Reflector Trim & Frame-In Kit. Select each separately.
Frame-In Kit Reflector Trims — See Individual Reflector Trim Specification Sheets
Open Downlight
Adjustable
Anodized
Anodized
Satin
Baffles
Basic
Eyeball
Enclosed Open
Wall
Reflector
Cone
Cone
White
Diffusers Wet Location Washer
1004IC
1045
1012
1008
1005
1071
1022
1021*
1081CD
1085*
1004ICQ**
1046
1012NM
1008NM 1005NM
1022WH
1024*
1081WH
1004ICN
1046CD
1013
1010
1005WH
1082
1177LX
1004ICNQ**
1013BK
1010NM 1005BNM
1088
1178LX
1013CD
1076
1088GW
1090*
1013NM
1076WH
1088WH
1013BKNM
1013CDNM
1013WH
* For Non-IC applications only.
**Supplied with integral push-In wire connectors
Frame-In Kit
Reflector Trim
7
1104IC
2
3
6
1
5
4
1004ICN
(Integral Nail)
Top View
Overall Length
1004IC/N: 9"
13 3/4" MIN.
24” MAX.
Overall Width
1004IC/N: 5 3/4"
Overall Height
1004IC/N: 7 1/2"
Features
1. Housing:
.032 (#20 ga.) aluminum. UL listed convertible IC/NON-IC. 2"
vertical adjustment in ceiling. Can be removed for access to junction box
and ceiling plenum. AirSeal
®
housing minimizes air leakage to less than 2
CFM at 1.57 PSF (or 75pa), which complies with Model Energy Code (Section
602.3.3) and Washington State Energy Code (Section 502.4) and reduces
heat loss and condensation in ceiling.
2. Mounting Frame:
.048 (#18 ga.) galvanized steel. Locks into position along
length of mounting bars with locking spring and bendable slot. (3) slots 90°
apart simplify alignment.
3. Junction Box:
2"X 4" X 3 1/2" (22 cu. in.) .032 (#22 ga.) galvanized steel.
UL listed for maximum 6 (#12 ga.) 1004IC/N 90°C through branch circuit con-
ductors. Integral cable clamps permit attachment of non-metallic (#12 or #14
ga.) Romex
®
cable without tools or additional connectors.
4. Mounting Bars:
.059 (#16 ga.) galvanized steel. Bars pivot for easy attach-
ment and wire-in below ceiling line. Bars extend to accommodate 16" to
24" O.C. joist spacing. The 1004IC features integral self-tapping philips
screws for secure attachment to wood or metal construction. The 1004ICN
features integral nails for secure attachment to wood. Both attach to T-bar
ceilings without the need of accessories.
5. Socket Housing:
Impact extruded aluminum or galvanized steel. Attached
trim retaining spring secures trim to any height on housing wall.
6. Socket:
Porcelain medium base: nickel plated screw shell. Pre-wired with
#18 ga. SF1 (300 VOLT 200° C) leads to junction box.
7. Thermal Protector:
Meets NEC and UL requirements. Located inside
housing.
Options & Accessories
AirSeal
®
Kit:
LAS56
NOTE:
Use only if factory installed tape or knockouts are removed from vertical
adjustment slots in housing wall.
Labels
UL (Type IC/NON-IC Convertible; Suitable for Damp Locations)
Complies with Air Leakage Requirements stated in the Model Energy Code and
the Washington State Energy Code.
AirSeal
®
is a registered trademark of Lightolier.
Romex
®
is a registered trademark of General Cable Industries Inc.
1004IC
(Integral Screw)
