Job Information
Type:
Job Name:
Cat. No.:
Lamp(s):
Notes:
"JSQPSU3PBE'BMM3JWFS."t t'BY
We reserve the right to change details of design, materials and finish.
XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt
Lighting Systems
A-8
1BHFPG
"MFSPOÜ4FSJFT-JHIU51FSh DN4FDUJPO
$
Features
1. Housing:
Extruded alu
m
inu
m
housing in lengths of 4’ (121.92c
m
), 8’ (243.84c
m
)
and 12’ (365.76c
m
). There are no exposed fasteners. The end caps are die-cast
alu
m
inu
m
sculpted and finished to
m
atch the housing.
2. Lens:
Extruded clear acrylic linear pris
m
atic lens.
3. Reflector:
Die-for
m
ed high purity anodized specular alu
m
inu
m
.
4. Lamping:
One T5 28W or 54W la
m
p per four-foot no
m
inal length. Provided
by others.
5. Alignment Mechanism:
The housing and the end cap each have a draw tight
m
echanis
m
that creates a hairline joint along and at the ends of the run. To
operate the
m
echanis
m
, the installer tightens two screws.
Labels
UL, cUL and I.B.E.W.
Finish
Powder coated baked white or silver ena
m
el.
Custo
m
colors available, consult factory.
Mountings
All
m
ounting is on 48” (121.92c
m
), 96” (243.84c
m
) and 144” (365.76c
m
) centers.
Cable Suspension
(not shown) 4-1/2" (11.43c
m
) dia
m
eter flat canopy finished
white ena
m
el, 1/16" (0.16c
m
) dia
m
eter stainless steel aircraft cable adjustable up
to 36" (91.44c
m
) and adjustable cable gripper. Cable
m
ounting at the ends of a run
is not available when track is being used. Installing ste
m
s at the ends of the run
will prevent the fixture fro
m
hanging off center caused by the weight of the track
fixture. Cable suspension can be used in the center of runs that have track
installed. Consult factory for other options.
Stem Mounting
(not shown) - 4-1/2" (11.43c
m
) dia
m
eter flat canopy, 1/4"
(0.64c
m
) IP (1/2” (1.27c
m
) OD) ste
m
. The ste
m
can acco
mm
odate up to 2-12 gauge
and 3-18 gauge solid wires. All co
m
ponents have a white finish.
Electrical
Ballast is <10% THD, 1.0 ballast factor, progra
m
start. Color-coded quick
connectors allow ease of connection for joiner
m
odules. For special circuiting
consult factory. Factory installed ballast disconnect allows the ballast to be
disconnected fro
m
and reconnected to inco
m
ing power under load without turning
the entire circtuit off.
Dimming:
120/277 VAC 1% di
mm
ing level, 4 or 5 wire feed required.
Emergency Battery Pack:
28 watt: 520 lu
m
ens @ 90
m
inutes, 54 watt: 700
lu
m
ens @ 90
m
inutes.
Ordering Instructions
Individual Fixtures:
1. Order nu
m
ber of MODULES required.
2. Order one POWER FEED END SET per MODULE.
Continuous Rows:
1. Deter
m
ine run length.
2. Order the appropriate nu
m
ber of MODULES for the co
m
plete run.
3. Order one POWER FEED END SET per run.
4. Order one INTERMEDIATE SUSPENSION per MODULE
m
inus one per run.
5. For runs that exceed a
m
perage li
m
its, order the appropriate nu
m
ber of
INTERMEDIATE POWER FEEDS.
Module Ordering Information
Family
Series
Track
Length
Shielding
Lamps
Finish
Options
A
1
B
D
A
= Track
B
= No Track
4
= 4-Foot
8
= 8-Foot
12
= 12-Foot
A
= No Shield
B
= Solid Shield
C
= Perf Shield
D
= Lens Shield
28
= 28w
54
= 54w
WH
= White
AL
= Aluminum
D1
= Dimming 120v
D2
= Dimming 277v
X5
= 5 Through Wires
Co
m
plete ordering instructions below.
6. Shielding:
3/16” (0.48c
m
) frosted acrylic lens with 85% trans
m
ission.
E1
= Emergency Pack, 120v
E2
= Emergency Pack, 277v
12-3/8” (31.43c
m
)
NOT TO SCALE
3-5/8” (9.21c
m
)
3
1
2
4
6
9-15/16”
(25.24c
m
)
