Liberty Pumps Wholesale Products Limited Warranty
Liberty Pumps, Inc. warrants that Liberty Pumps wholesale products are free from all factory
defects in material and workmanship for a period of three (3) years from the date of purchase
(excluding batteries). The date of purchase shall be determined by a dated sales receipt noting
the model and serial number of the pump. The dated sales receipt must accompany the
returned pump if the date of return is more than three years from the date of manufacture
noted on the pump nameplate.
The manufacturer's sole obligation under this Warranty shall be limited to the repair or
replacement of any parts found by the manufacturer to be defective, provided the part or
assembly is returned freight prepaid to the manufacturer or its authorized service center, and
provided that none of the following warranty-voiding characteristics are evident:
The manufacturer shall not be liable under this Warranty if the product has not been properly
installed, operated, or maintained per manufacturer instructions; if it has been disassembled,
modified, abused, or tampered with; if the electrical cord has been cut, damaged, or spliced; if
the pump discharge has been reduced in size; if the pump has been used in water tempera-
tures above the advertised rating; if the pump has been used in water containing sand, lime,
cement, gravel, or other abrasives; if the product has been used to pump chemicals, grease, or
hydrocarbons; if a non-submersible motor has been subjected to moisture; or if the label
bearing the model and serial number has been removed.
Liberty Pumps, Inc. shall not be liable for any loss, damage, or expenses resulting from
installation or use of its products, or for indirect, incidental, and consequential damages,
including costs of removal, reinstallation or transportation.
There is no other express warranty. All implied warranties, including those of merchantability
and fitness for a particular purpose, are limited to three years from the date of purchase. This
Warranty contains the exclusive remedy of the purchaser, and, where permitted, liability for
consequential or incidental damages under any and all warranties are excluded.
“Acceptable For Indoor Use Only”
“Nonsubmersible Pump”
“CAUTION” – To reduce risk of electric shock, install with motor and all electrical
components above the top grade level of the sump. This pump is not submersible.
“WARNING”
“Risk Of Electric Shock – This pump has not been investigated for use in swimming pool
or marine areas.”
“To reduce risk of electric shock, see instruction manual for proper installation.”
“To reduce risk of electric shock, connect only to a properly grounded, grounding-type
receptacle.”
“THERMALLY PROTECTED”
Date of Production: stamped on reservoir.
“FOR INDOOR USE ONLY”
”ENCLOSURE TYPE 2”
LIMITED WARRANTY
7000 Apple Tree Avenue Bergen, NY 14416
Phone 800-543-2550 Fax 585-494-1839
www.LibertyPumps.com
Unit does not run.
Unit makes loud noises even
after the first dry-running
phase.
Unit runs but does not pump
the liquid out properly.
Check the highest point of the discharge hose
does not exceed the maximum delivery head of
the pump.
Check hose is not clogged or kinked.
Check the flow rate of the pump is sufficient for
the condensation volume of air conditioner.
Check if pump has contact with any hard surfaces.
If it does, anti-vibration materials should be
positioned between the pump and all hard
surfaces.
Verify there is no siphoning action.
Check the power supply.
Check the air conditioner to see if condensation is
actually being produced.
Check hose is not clogged or kinked.
Ensure power to the pump is disconnected before performing any service or maintenance.
1) Clean the reservoir every six months, preferably at the beginning and end of the air
conditioning season.
a) Open the reservoir cover using the opening latch.
b) Clean the reservoir and float using a solution of water containing 5% bleach.
c) Replace the float in the initial position (magnet facing UP).
d) Reinstall the reservoir cover.
2) Perform a
TEST OPERATION
[see above].
After installation, test pump operation by slowly pouring water into the air conditioner
drain pan. Repeat this approx. 8–10 times.
Check for any water leaks, kinked or pinched lines, or siphoning action.
Clicking noises heard at initial start-up are normal and are usually only heard for the first
few operations.
Allow a one minute rest after each cycle to prevent triggering the thermal protector.
CONFORMS TO ANSI/UL STD. 778
CERTIFIED TO CAN/CSA STD. C22.2 NO.108
4007096
SERVICE & MAINTENANCE
TEST OPERATION
TROUBLESHOOTING
PRODUCT INFORMATION
–
5
–
LCU-MS Mini-Split Series
USER GUIDE
Read this user guide carefully before attempting to install, operate, or
service the LCU-MS Mini-Split Series pump. Know the pump application,
limitations, and potential hazards. Protect yourself and others by observing
all safety information. Failure to comply with these instructions could result
in personal injury and/or property damage. Retain this user guide for future
reference. Installation, connections, and service shall be done only by
qualified personnel.
7000 Apple Tree Avenue
Bergen, NY 14416
Phone 800-543-2550
Fax 585-494-1839
www.LibertyPumps.com
For Air Conditioners up to 7 kW
LCU-MS2
(LCU-MS + DUCTS)
LCU-MS
CEILING
DRAIN PAN
MADE IN SOUTH KOREA
Pump Model #: _____________________________________________
Pump Serial #: ______________________________________________
Install Date: _________________________________________________
Keep this manual handy for future reference
Retain dated sales receipt for warranty
✔ ✖
2035000A
