Liberty Pumps LGH Series Installation Manual Download Page 1

Page: 1 / 14

Installation

Manual

For pressure sewer applications

, verify a Redundant

Check Valve Assembly (curb stop and check valve) is

installed between the pump discharge and the street

main, as close to the public right-of-way as possible, on all

installations to protect from system pressures.

Installer: manual must remain with owner or

system operator/maintainer.

Record information from pump nameplate:

Model:

Serial:

Control Panel:

Mfg Date:

Install Date:

Dealer:

Dealer Ph:

7000 Apple Tree Avenue

Bergen, NY 14416

ph: 1-800-543-2550

fax: 1-585-494-1839

www.LibertyPumps.com/LEP

7550000G

LGV-Series

LGH-Series

Ordinary Location Models

XLGV-Series

XLGH-Series

Approved for Hazardous Locations

Class 1, Division 1, Groups C and D

Class 1, Zone 1, Groups IIA and IIB

3–15 hp

Submersible

Grinder Pumps

Summary of Contents for LGH Series















Search results

Summary of Contents for LGH Series

Reviews:

Related manuals for LGH Series

Brands by name

Popular brands

Liberty Pumps LGH Series, Installation Manual

Search results

Summary of Contents for LGH Series

Reviews:

Related manuals for LGH Series

Brands by name

Popular brands