background image

AS-2H-WP Installation Guide

3

1. 

Read these instructions – All the safety and operating instructions should be read before this product is operated. 

2. 

Keep these instructions – The safety and operating instructions should be retained for future reference. 

3. 

Heed all warnings – All warnings on the appliance and in the operating instructions should be adhered to. 

4. 

Follow all instructions – All operating and use instructions should be followed. 

5. 

Do not use this apparatus near water – The appliance should not be used near water or moisture – for example, in a wet 

basement or near a swimming pool, and the like. 
6. 

Clean only with a dry cloth. 

7. 

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 

8. 

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) 

that produce heat. 
9. 

Do not defeat the safety purpose of the polarized plug. A polarized plug has two blades with one wider than the other. 

The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an 

electrician for replacement of the obsolete outlet. 

10. 

Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the 

point where it exits from the apparatus. 

11. 

Only use attachments/accessories specified by the manufacturer. 

12. 

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the 

apparatus. When a cart or rack is used, use caution when moving the cart/ apparatus combination to avoid injury 

from tip-over. 

13. 

Unplug the apparatus during lighting storms or when unused for long periods of time. 

14. 

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any 

way, such as; the power-supply cord or plug is damaged, liquid has been spilt or objects have fallen into the apparatus, the 

apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 

15. 

CAUTION: Servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do 

not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. 

16. 

Do not install this equipment in a confined or built-in space such as a book case or similar unit. The equipment must 

remain in well ventilation conditions. Ventilation should not be impeded by covering the ventilation openings with items 

such as newspaper, table-cloths, curtains etc. 
17. 

WARNING: Only use attachments/accessories (such as the battery etc.) specified or provided by the manufacturer. 

18. 

WARNING: Refer to the information on the underside of the enclosure for electrical and safety information before 

installing or operating the apparatus. 

19. 

WARNING: To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture. The apparatus 

shall not be exposed to dripping or splashing and objects filled with liquids, such as vases, shall not be placed on apparatus.

20. 

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

21. 

WARNING: The battery shall not be exposed to excessive heat such as sunshine, fire or the like.

22. 

WARNING: The all-pole mains switch located on rear panel is used as the disconnect device, the switch shall remain 

readily operable.

23. 

WARNING: DO NOT INGEST BATTERY. CHEMICAL BURN HAZARD.

24. 

Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the 

product and keep it away from children.

25. 

If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical 

attention.

Important Safety Instructions

Summary of Contents for Intelix AS-2H-WP

























Reviews: