LIBERTY AV SOLUTIONS Intelix AS-2H-WP Installation And Operation Manual Download Page 19

Page: 19 / 24

AS-2H-WP Installation Guide

EDID Configuration

Description

Command

Response

UHD/30

EDID UHD<CR><LF>

EDID UHD!<CR><LF>

1080p

EDID FHD<CR><LF>

EDID FHD!<CR><LF>

720p

EDID HD<CR><LF>

EDID HD!<CR><LF>

1920x1200

EDID WUXGA<CR><LF>

EDID WUXGA!<CR><LF>

1360x768

EDID WXGA2<CR><LF>

EDID WXGA2!<CR><LF>

1280x800

EDID WXGA<CR><LF>

EDID WXGA!<CR><LF>

1600x1200

EDID UXGA<CR><LF>

EDID UXGA!<CR><LF>

1400x1050

EDID SXGAP<CR><LF>

EDID SXGAP!<CR><LF>

1024x768

EDID XGA<CR><LF>

EDID XGA!<CR><LF>

EDID from display

EDID PT<CR><LF>

EDID PT!<CR><LF>

Get EDID setting

GET EDID<CR><LF>

EDID PT!<CR><LF>

The EDID settings listed below will be passed to both HDMI inputs.

Summary of Contents for Intelix AS-2H-WP

























Search results

Summary of Contents for Intelix AS-2H-WP

Reviews:

Related manuals for Intelix AS-2H-WP

Brands by name

Popular brands

LIBERTY AV SOLUTIONS Intelix AS-2H-WP, Installation And Operation Manual

Search results

Summary of Contents for Intelix AS-2H-WP

Reviews:

Related manuals for Intelix AS-2H-WP

Brands by name

Popular brands