manualshive.com logo in svg

LI-COR LI-6400, Manual

The LI-COR LI-6400 is an advanced scientific instrument for measuring photosynthesis and gas exchange in plants. For a comprehensive understanding of its functionalities and operation, a user manual is available for download, free of charge, from our website.

Share
Download
background image

Troubleshooting

New Measurements Mode Warning Messages

Using the LI-6400

20-7

New Measurements Mode Warning Messages

In New Measurements mode, a variety of messages can appear in the second
line of the display. This section lists, in decreasing order of severity, the mes-
sages and their meanings.

These warning messages are generated by a function that runs every 10 sec-
onds while in New Measurements mode, so they appear or disappear at 10
second intervals. (A message may linger for up to 10 seconds after the offend-
ing condition has been remedied.)

These messages can be suppressed (and re-enabled) by pressing 

ctrl

 + 

z

 (in

New Measurements mode only). Also note that every time New Measure-
ments mode is entered, the messages are re-enabled automatically.

ÒBLOWN FUSE (Analyzer or Flow)Ó

Instruments having serial number 401 and above are equipped with a back
plane board that is modified to allow detection of a blown fuse. Two fuses can
be detected: the analyzer board fuse, and the flow board fuse. It cannot tell
which one is blown, just that one or both are blown. See 

Replacing the Fuses

on page 19-10.

ÒIRGAs Not ReadyÓ

Refer to the discussion starting on page 20-14.

ÒHigh Humidity AlertÓ

The lowest value 

T

 of the three temperatures measured in or near the chamber

(analyzer block, chamber air, and leaf) is used to compute a relative humidity

RH

alert

:

 (20-1)

where 

W

s

 is sample water concentration (mmol mol

-1

), 

P

 is ambient pressure

(kPa), and the function 

e

s

() computes saturation vapor pressure (kPa) as a

function of temperature (C) (Equation (14-21) on page 14-10). If 

RH

alert

 ex-

ceeds 95%, the ÒHigh Humidity AlertÓ message appears. The usual remedy
is some combination of the following:

¥

Give the coolers a warmer target.

Perhaps youÕre asking for a block or leaf temperature that is too cold.

RH

alert

W

s

P

1000

------------

e

s

T

( )

--------------------

100

´

=

Summary of Contents for LI-6400















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LI-6400

Qingdao H.Y AP300 Manual preview
AP300
Brand: Qingdao H.Y Pages: 6
KaVo 4040 Operating, Maintenance And Assembly Instructions preview
4040
Brand: KaVo Pages: 16
GE MicroVersaTrip Plus Installation Instructions Manual preview
MicroVersaTrip Plus
Brand: GE Pages: 20
GE MicroVersaTrip Plus Manual preview
MicroVersaTrip Plus
Brand: GE Pages: 2
GE b30 Technical Reference Manual preview
b30
Brand: GE Pages: 252
Balanced Body Duet Manual preview
Duet
Brand: Balanced Body Pages: 12
Eagle Pro EL Series Instruction Sheet preview
EL Series
Brand: Eagle Pro Pages: 6
GE EntelliGuard G Instructions Manual preview
EntelliGuard G
Brand: GE Pages: 10
Bang & Olufsen BeoPlay A9 Quick Manual preview
BeoPlay A9
Brand: Bang & Olufsen Pages: 2
YYZ Lighting LYNX Installation preview
LYNX
Brand: YYZ Lighting Pages: 3
Camp Safety COBRA Manual preview
COBRA
Brand: Camp Safety Pages: 118
Ultrafast Systems KRONOS User Manual preview
KRONOS
Brand: Ultrafast Systems Pages: 39
Mackworth HOLLY User Instructions preview
HOLLY
Brand: Mackworth Pages: 2
GE PANDA Service Manual preview
PANDA
Brand: GE Pages: 212
Wahl 1911 Quick Manual preview
1911
Brand: Wahl Pages: 2
PAS Systems International PAS V Instruction Manual preview
PAS V
Brand: PAS Systems International Pages: 24
PAS Systems International MARK V Alcovisor Operating Manual preview
MARK V Alcovisor
Brand: PAS Systems International Pages: 20
PARRY CPC Product Instructions preview
CPC
Brand: PARRY Pages: 14

Brands by name

Popular brands

Load more brands