background image

Your Safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read 

and obey all safety messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word DANGER or WARNING.
These words mean:

w

DANGER:

  

You can be killed or seriously injured if you don’t immediately follow instructions.

w

WARNING:

 You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of 

injury, and tell you what can happen if the instructions are not followed. 

BASIC SAFETY PRECAUTIONS

w

WARNING: 

To reduce the risk of fire, electric shock, or injury to persons when using this  

appliance, follow basic precautions, including the following:
•  Read all instructions before using the dryer.
•  Before use, the dryer must be properly installed 

as described in this manual.

•  Do not place items exposed to cooking oils in 

your dryer. Items contaminated with cooking 

oils may contribute to a chemical reaction that 

could cause a load to catch fire. 

•  Do not dry articles that have been previously 

cleaned in, washed in, soaked in, or spotted 

with gasoline, dry-cleaning solvents, or other 

flammable or explosive substances as they give 

off vapors that could ignite or explode.

•  Do not reach into the dryer if the drum or any 

other part is moving.

•  Do not repair or replace any part of the dryer 

or attempt any servicing unless specifically 

recommended in this Use and Care Guide or 

in published user-repair instructions that you 

understand and have the skills to carry out.

•  Do not tamper with controls.
•  Before the dryer is removed from service or 

discarded, remove the door to the drying 

compartment.

•  Do not allow children to play on or in the dryer. 

Close supervision of children is necessary when 

the dryer is used near children.

•  Do not use fabric softeners or products to 

eliminate static unless recommended by the 

manufacturer of the fabric softener or product.

•  Do not use heat to dry articles containing 

foam rubber or similarly textured rubber-like 

materials.

•  Keep area around the exhaust opening and 

adjacent surrounding areas free from the 

accumulation of lint, dust, and dirt.

•  The interior of the dryer and exhaust vent 

should be cleaned periodically by qualified 

service personnel.

•  Do not install or store the dryer where it will be 

exposed to the weather.

•  Always check the inside of the dryer for foreign 

objects.

•  Clean lint screen before or after each load.
•   Do not store or use gasoline or other flammable 

vapors and liquids in the vicinity of this appli-

ance or any other appliances.

•  Installation and service must be  

performed by a qualified installer, service 

agency.

•  This appliance is not intended for use by 

  persons (including children) with reduced 

  physical, sensory or mental capabilities, or lack 

of experience and knowledge, unless they have 

been given supervision or instruction concerning 

use of the appliance by a person responsible for 

their safety.

READ ALL INSTRUCTIONS BEFORE USE

w

WARNING 

For your safety, the information in this manual must be  

followed to minimize the risk of fire or explosion, electric shock, or to prevent 
property damage, personal injury, or loss of life.

Summary of Contents for STEAM DRYERS TD-V1000S





































Reviews: