LG STB-3000 Setup Manual Download

Page: 63 / 86

206-4272

Reference: Updating STB Software using a USB Memory Device

This section describes how to update STB (CPU) and/or PTC software using the STB Manager /

USB Download Menu “Update STB Software” and/or “Update PTC Software” option(s), respectively,

though you may also use the Ez Download utility to update software, if desired. See “Ez Download

Utility” on pages 26 to 29 for further information.

Before You Begin

•

Software update files must be stored in a folder named “LG_DTV” in the root directory of the

USB memory device.

• Ensure the USB device has been formatted with FAT format.

Update the STB/PTC Software

Note:

You can check the STB/PTC software versions by accessing the Installer Menu with the

Installer Remote. See “Accessing the Installer Menu” on page 30 for further information. PTC and

CPU versions are displayed in the Installer Menu footer.

Note for STB CPU Software Update only:

If the STB detects a software file on the USB

device, it will automatically display an Update STB Software screen, and if the file contains a later

version of software than is currently running on the STB, you can start the software update from

this screen (select

UPDATE

and press

). Otherwise, you can exit the screen (select

CANCEL

and press

), and access the STB Manager / USB Download Menu as described below.

1. Turn ON the STB/display panel, and then insert the USB memory device into either of the USB

ports on the STB.

2. Press

MENU

on the Installer Remote to display the STB setup menus (STB is in Pass-through

Mode) or the Function Menu (STB is not in Pass-through Mode).

3. Use the arrow navigation keys to select/highlight either the

General

menu icon from the STB

setup menus or the

Safety

menu icon from the Function Menu. Then, press the number “

”

key a total of seven times to display the STB Manager / USB Download Menu.

4. With the STB Manager / USB Download Menu on display, use the Up/Down arrow keys to

select

Update STB Software

Update PTC Software

, as applicable, and press

Note:

The STB Manager / Diagnostics Menu is for service use only.

CANCEL

STB MANAGER

USB Download Menu

Diagnostics Menu

Ez Download

Update STB Software

Update PTC Software

Teach To STB (TLX)

(Continued on next page)

Summary of Contents for STB-3000























































































Search results

Summary of Contents for STB-3000

Reviews:

Related manuals for STB-3000

Brands by name

Popular brands

LG STB-3000, Setup Manual

Search results

Summary of Contents for STB-3000

Reviews:

Related manuals for STB-3000

Brands by name

Popular brands