LG OK99 Service Manual Download Page 31

Page: 31 / 85

3-6

Only for training and service purposes.

ONE POINT REPAIR GUIDE

4. NO BOOTING IN CD/USB FUNCTION

After you turn on power key and displayed message in the following order (HELLO



VOL XX



or USB) on VFD, it will not display other message on VFD, and it will not boot-up normally.

4-1. NO DVCC_3.3V, 1.2 VA

4-1-1. Solution

Please check and replace IC202, IC204, IC205 on MAIN board.

4-1-2. How to troubleshoot (Countermeasure)

1) Check voltage of IC202 AND IC205 pin4 on MAIN board.



If IC202, IC205 pin4(about 5.1 V) Input 5.1 VA doesn’t come out, check 5.1 VA from SMPS board.

2) If IC202, IC205 pin4(about 5.1 V) is normal, check the PWR_CTRL(IC204 pin5) is high (about 3.3 V).



If PWR_CTRL isn’t high, check pin D11 of IC501 & R5B78, R214, R233.

3) If PWR_CTRL is high, check R5B78 and if there’s no defective component then check IC204 pin1 short
with GND.
4) If 3.3 V(DVCC_3.3V) is normal, check 1.2 VA output(C221, C226, C287, C288, C229) voltage of IC205.



If 1.2 VA of IC205 doesn’t come out, then replace IC205.

4-1-3. Service hint (Any picture / Remark)

< MAIN board top view >

< MAIN board bottom view >

IC204

IC205

IC202

Summary of Contents for OK99












































































Search results

Summary of Contents for OK99

Reviews:

Related manuals for OK99

Brands by name

Popular brands

LG OK99, Service Manual

Search results

Summary of Contents for OK99

Reviews:

Related manuals for OK99

Brands by name

Popular brands