manualshive.com logo in svg

LG MultiSITE VM3, Startup Manual, Page: 4 / 56

Share
Download
LG MultiSITE VM3 Startup Manual Download Page 4

4

LG MultiSITE

TM 

VM3

Due to our policy of continuous product innovation, some specifications may change without notification.  

©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG” is a registered trademark of LG Corp.

 Do not use or store flammable gas or combustibles near the unit. 

There is risk of fire, explosion, and physical injury or death. 

Disconnect power before installing or servicing the unit.

There is risk of physical injury or death due to electric shock. 

 

 Do not touch any exposed outdoor unit wiring, terminals, or other electrical components with tools or exposed skin. Only 

qualified technicians should install, use, or remove this unit. 

Improper installation or use may result in fire, explosion, electric shock, physical injury and/or death.

TABLE OF SYMBOLS

The instructions below must be followed to prevent product malfunction, property damage, injury or death to the user or other people. Incor-

rect operation due to ignoring any instructions will cause harm or damage. The level of seriousness is classified by the symbols described 

below.

SAFETY INSTRUCTIONS

DANGER

This symbol indicates an imminently hazardous situation which, if not avoided, will result in death or 

serious injury.

WARNING

This symbol indicates a potentially hazardous situation which, if not avoided, could result in death or 

serious injury.

CAUTION

This symbol indicates a potentially hazardous situation which, if not avoided, may result in minor or 

moderate injury.  

Note:

This symbol indicates situations that may result in equipment or property damage accidents only.

This symbol indicates an action that should not be performed.

This document describes the initial Niagara 4 software installation and configuration for a QNX-based LG MultiSITE

TM

 VM3 controller, using 

LG MultiSITE

TM

 Supervisor (versions Niagara 4.1 and later). 

Refer to the LG MultiSITE

TM

 VM3 Installation Manual for installation instructions for the controller. 

DANGER

Summary of Contents for MultiSITE VM3

























































Reviews:

No comments