H O W TO U S E
H O W TO U S E
CYCLE SETTING BUTTONS
TEMP. CONTROL
Adjusts the temperature setting
from ULTRA LOW to HIGH. This
allows precise care of your fabrics
and garments. Press the TEMP.
CONTROL button repeatedly to scroll through
available settings.
TIME DRY
Allows you to manually select the
drying time, from 20 to 60 minutes,
in 10-minute increments. Use
this for small loads or to remove
wrinkles. Use the MORE TIME/LESS TIME
buttons to add or reduce the drying time in 1-
minute increments.
BEEPER
Adjusts the volume of the end-
of-cycle beeper, or turns off the
beeper.
DRY LEVEL
Selects the level of dryness for
the cycle. Press the DRY LEVEL
button repeatedly to scroll through
available settings.
• This option is only available with SENSOR
DRY cycles.
• The dryer will automatically adjust the cycle
time. Selecting VERY DRY or MORE DRY
will increase the cycle time, while LESS
DRY or DAMP DRY will decrease the cycle
time.
• Use a LESS DRY or DAMP DRY setting for
items that you wish to iron.
DRY
LEVEL
TEMP.
CONTROL
TIME
DRY
BEEPER
SENSOR DRY cycles have preset settings
that are selected automatically and cannot be
changed. MANUAL DRY cycles have default
settings, but you may also customize the
settings using the cycle setting buttons. Press
the button for that option to view and select
other settings.
NOTE:
To protect your garments, not every
dryness level, temperature, or option is
available with every cycle. See the Cycle
Guide for details.
OPERATING THE DRYER
Press the ON/OFF button to turn on the
dryer. The lights around the cycle
selector knob will illuminate.
Turn the cycle selector knob to the desired
cycle. The display will show
the preset Dry Level,
Temperature, Time, and
Option settings for that cycle.
If you would like to change the settings
for that cycle, press the option button(s)
to display additional settings for that option. Press
the button again to cycle through the settings until
the desired setting is highlighted.
NOTE:
To protect your garments, not every dry level,
temperature, or option is available with every cycle.
1
2
3
Select any additional cycle options, such as ANTI-
BACTERIAL, DAMP DRY BEEP, FLOW
CHECK, WRINKLE CARE, or RACK DRY
by pressing the button for that option.
4
Once you have loaded the dryer:
Press the START/PAUSE button to begin the
cycle. The display will change,
and the dryer will display the
estimated (SENSOR DRY) or set
time (MANUAL DRY) remaining
and start tumbling. To pause the cycle at any
time, open the dryer door or press PAUSE.
To resume the cycle where it was stopped,
press START/PAUSE again.
NOTE:
If the dryer has been stopped for
more than 8 minutes, the dryer will turn
off automatically.
5
When the load is finished, the beeper (if
set) will sound. If you have set the WRINKLE
CARE option, the dryer will tumble the load
periodically for up to 3 hours.
To prevent wrinkling, remove items from the
dryer immediately after the end of the cycle.
6
Always clean the lint filter after every cycle.
To clean, pull the lint filter straight up and
roll any lint off the filter with your fingers.
Do not rinse or wash the filter to remove lint.
Push the lint filter firmly back into place.
7
DRY
LEVEL
TEMP.
CONTROL
TIME
DRY
BEEPER
OPTION
*LANGUAGE
30
Summary of Contents for DLEX0001TM
Page 49: ...NOTES NOTES 49 ...
Page 142: ...NOTES REMARQUES NOTES REMARQUES 142 ...
Page 143: ...NOTES REMARQUES NOTES REMARQUES 143 ...
Page 144: ...P No 3828EL3010G ...
