LG CodePlus HCS6300 Series Installation & Setup Manual Warranty Download Page 10

Page: 10 / 52

206-4122

HCS6300 Functional Blocks

Slot 1
Slot 2

Slot 4
Slot 5

Slot 8
Slot 9

Slot 11
Slot 12

38 Mbps

256-QAM

Modulator

2:1 MUX

Upconverter

Transport

Streams from

Transcoder

Cards

MUX

Blocks

MOD

Blocks

Upconverter

Block

RF Out

4 Contiguous

CATV Channels

HCS6300

Service

Port

Ethernet

256-QAM

Modulator

256-QAM

Modulator

256-QAM

Modulator

The HCS6300 consists of four main functional blocks:
• MUX: Four parallel multiplexers, each of which can combine up to two encrypted transport

streams into a single 38 Mbps transport stream. The transport streams from the transcoder

cards are supplied to the HCS6300 through the internal backplane circuit board of the card

frame.

• MOD: Four parallel 256-QAM modulators that take the MUX output streams and produce

four modulated outputs.

• Upconverter: This block takes the modulated output streams from the MOD block and places

them on up to four contiguous cable RF channels. The output of this block is a combined RF

signal four channels wide.

• Controller: Provides the PC interface for HCS6300 setup and configuration.

HCS6300 default settings assign the inputs of each channel MUX to specific slots in the

CodePlus card frame, where the RF start channel is assigned to card frame Slots 1 & 2, the

second channel is assigned to card frame Slots 4 & 5, etc.

Summary of Contents for CodePlus HCS6300 Series




















































Search results

Summary of Contents for CodePlus HCS6300 Series

Reviews:

Related manuals for CodePlus HCS6300 Series

Brands by name

Popular brands

LG CodePlus HCS6300 Series, Installation & Setup Manual Warranty

Search results

Summary of Contents for CodePlus HCS6300 Series

Reviews:

Related manuals for CodePlus HCS6300 Series

Brands by name

Popular brands