manualshive.com logo in svg

LG AT-C186PLE0, Installation Manual, Page: 24 / 28

Share
Download
LG AT-C186PLE0 Installation Manual Download Page 24

Installation 

 

Installer Setting - Setting

 

Address

  of  Central

 

Control

Installer Setting - Checking Address of Central Control

1

. With the PLASMA button pressed, press the RESET button.

2

. Press the ON/OFF button toward the indoor unit 1 time, and the indoor unit will display the set

address in the display window.

• The address display time and method can differ by the indoor 

unit type.

3

. Reset the remote controller to use the general operation mode

.

1

. With the MODE button pressed, press the

RESET button.

2

. By using the temperature setting button,

set the indoor unit address.

• Setting range : 00 ~ FF

3

. After setting the address, press the

ON/OFF button toward the indoor unit 1
time.

4

. The indoor unit will display the set address

to complete the address setting.

• The address display time and method can

differ by the indoor uint type.

5

. Reset the remote controller to use the

general operation mode.

24

    Ceiling Cassette Air Conditioner

LG

Summary of Contents for AT-C186PLE0





























Reviews:

No comments