manualshive.com logo in svg

LG ABNQ18GHLA0, Svc Manual, Page: 38 / 100

Share
Download
LG ABNQ18GHLA0 Svc Manual Download Page 38

Part 4  Trouble Shooting 

- 38 -

Copyright ©2013 LG Electronics. Inc. All right reserved.
Only for training and service purposes

LGE Internal Use Only

4. Trouble Shooting 

1. Self-diagnosis Function.................................................................................................39

1.1 Error Indicator (Indoor)................................................................................................39
1.2 Error Indicator (Outdoor) .............................................................................................40

2. Pump Down.....................................................................................................................41

3. Evacuation ......................................................................................................................42

4. Gas Charging ..................................................................................................................43

5. Cycle Part ........................................................................................................................44

6. Electronic Parts ..............................................................................................................45

6.1 The Product doesn t operate at all ..............................................................................45

6.2 The Product doesn't operate with the remote controller .............................................46

6.3 The Compressor/Outdoor Fan are don't operate ........................................................47

6.4 When indoor Fan does not operate.............................................................................48

6.5 When the louver does not operate. .............................................................................49

6.6 Troubleshooting Indoor Error  .....................................................................................50

6.7 Troubleshooting Outdoor Error  ..................................................................................56

Summary of Contents for ABNQ18GHLA0





































































































Reviews:

No comments