LG ABNQ18GHLA0 Svc Manual Download Page 34

Page: 34 / 100

- 34 -

LGE Internal Use Only

ELEVATION GRILL (REMOTE CONTROLLER_Accessory)

• How to Use Remote Controller

• Main Components of Lift Grill

As for operation of Remote Controller, use it by directing the trans-
mitter part of Remote Controller to the receiver part of front panel
directly under front panel.

• Do not drop it down or into water. Or else there is worry about

trouble failure.

• Do not press hard the Remote Controller button with nail (ball-

point pen or other sharp substance). Or else there is worry
about trouble failure.

• In case when obstacle such as curtain hides the signal reception

part of receiver in between the space interval, Remote Controller
operation is infeasible.

Lift grill front panel assembly

Bolts for installation (4 EA, P/No. 3A00255K)

Instruction manual

√

Remote Controller for lift grill

Ascend

Signal transmitter

Descend

Stop

Part 2 Functions & Controls

Summary of Contents for ABNQ18GHLA0





































































































Search results

Summary of Contents for ABNQ18GHLA0

Reviews:

LG ABNQ18GHLA0, Svc Manual, Page: 34 / 100

Search results

Summary of Contents for ABNQ18GHLA0

Reviews: