LG-Ericsson ipldk-60 Feature Description And Operation Manual Download Page 447

Page: 447 / 512

ipLDK-60

Issue 2.0

Admin Programming Manual

July, 2010

172

3.9.12 Mobil Extension (PGM 236)

PGM 236 configures the characteristics of a Mobile Extension associated with each station port.

Procedure:

1. Press

the

[TRANS PGM]

button.

2. Dial

236.

3. Dial a table index ‘01’ ~ ‘48’ for a station port

4. Select the desired Flexible button.

5. Enter the appropriate value.

6. Press

the

[Hold/Save]

button.

PGM

236

Flex

Btn

Description

Default

Values

Allow Mobile

Extension

When enable (On), the system allows the station to activate the Mobile Extension

feature.

0 (Off)

0 = Off

1 = On

CO Group

This parameter assigns the CO line group to use when the system calls the Mobile

Extension. An ISDN or IP CO line group must be used.

01 ~ 24

Telephone Number

This parameter assigns the number the system dials to call the Mobile Extension.

Not assigned

Up to 24 digits

CLI Number

This parameter assigns the CLI the system receives for an incoming call from the

Mobile Extension.

Not Assigned

Up to 16 digits

Mobile Extension

Hunt Call

When enabled (On), Hunt group calls to the associated station alert to the Mobile

Extension.

0 (Off)

0 = Off

1 = On

Voice Message

Notification

When enable (On), the system sends an SMS to the Mobile when a voice mail is

received for the associated station. PSTN SMS must be available.

0 (Off)

0 = Off

1 = On

Mobile Extension

Usage

When enabled (On), the Mobile Extension feature is activated. This is the same as

the user dialing ‘34’ to Activate Mobile Extension.

0 (Off)

0 = Off

1 = On

Summary of Contents for ipldk-60

































































































































































































































































































































































































































































































































Search results

Summary of Contents for ipldk-60

Reviews:

Brands by name

Popular brands

LG-Ericsson ipldk-60, Feature Description And Operation Manual

Search results

Summary of Contents for ipldk-60

Reviews:

Brands by name

Popular brands