LG-Ericsson ipldk-60 Feature Description And Operation Manual Download Page 336

Page: 336 / 512

ipLDK-60

Issue 2.0

Admin Programming Manual

July, 2010

3.3.2

CO Line Attributes I (PGM 141)

PGM 141 is one of three PGMs that assign general attributes to the CO line range. Also, see PGMs 142 and 146.

Procedure:

1. Press

the

[TRANS/PGM]

button.

2. Dial

141.

3. Enter the appropriate CO line Range.

4. Select the desired Flexible button.

5. Enter the appropriate value.

6. Press

the

[Hold/Save]

button.

PGM

141

Flex

Btn

Description

Default

Values

CO line Group

This parameter defines the CO Group for the CO lines. Each CO line is assigned to

a CO Group with other CO lines having similar characteristics. Group 00 is for

Private lines and Group 25 is for unused lines.

00 ~ 25

CO COS

This parameter defines the Class Of Service (COS) for CO lines. The CO COS is

combined with Station COS (PGM 116) to determine dialing restrictions for a call.

CO COS 1: Station COS applies

CO COS 2: Exception Table A governs

CO COS 3: Exception Table B governs

CO COS 4: Restricts LD calls and Exception Table C

CO COS 5: Overrides Station COS 2~6 with no restrictions.

1 ~ 5

DISA Account

Code

When enabled (On), DISA callers attempting to place a CO line call must enter a

Station or System Authorization Code (PGM 227).

1 (On)

0 = Off

1 = On

CO Line Assign

This parameter determines the ‘Start’ and ‘Disconnect’ signal for the CO line, Loop

0 (Loop)

0 = Loop

Summary of Contents for ipldk-60

































































































































































































































































































































































































































































































































Search results

Summary of Contents for ipldk-60

Reviews:

Brands by name

Popular brands

LG-Ericsson ipldk-60, Feature Description And Operation Manual

Search results

Summary of Contents for ipldk-60

Reviews:

Brands by name

Popular brands