LG-Ericsson iPECS ES-4526G User Manual Download Page 804

Page: 804 / 1328

HAPTER

| General Security Measures

ARP Inspection

– 804 –

ES-4500G Series

XAMPLE

Console#show ip source-guard binding

MacAddress IpAddress Lease(sec) Type VLAN Interface

----------------- --------------- ---------- -------------------- ---- --------

11-22-33-44-55-66 192.168.0.99 0 Static 1 Eth 1/5

Console#

ARP I

NSPECTION

ARP Inspection validates the MAC-to-IP address bindings in Address

Resolution Protocol (ARP) packets. It protects against ARP traffic with

invalid address bindings, which forms the basis for certain “man-in-the-

middle” attacks. This is accomplished by intercepting all ARP requests and

responses and verifying each of these packets before the local ARP cache is

updated or the packet is forwarded to the appropriate destination,

dropping any invalid ARP packets.

ARP Inspection determines the validity of an ARP packet based on valid IP-

to-MAC address bindings stored in a trusted database – the DHCP snooping

binding database. ARP Inspection can also validate ARP packets against

user-configured ARP access control lists (ACLs) for hosts with statically

configured IP addresses.

This section describes commands used to configure ARP Inspection.

Table 82: ARP Inspection Commands

Command

Function

Mode

ip arp inspection

Enables ARP Inspection globally on the switch

ip arp inspection filter

Specifies an ARP ACL to apply to one or more

VLANs

ip arp inspection log-buffer

logs

Sets the maximum number of entries saved in a

log message, and the rate at these messages are

sent

ip arp inspection validate

Specifies additional validation of address

components in an ARP packet

ip arp inspection vlan

Enables ARP Inspection for a specified VLAN or

range of VLANs

ip arp inspection limit

Sets a rate limit for the ARP packets received on a

port

ip arp inspection trust

Sets a port as trusted, and thus exempted from

ARP Inspection

show ip arp inspection

configuration

Displays the global configuration settings for ARP

Inspection

show ip arp inspection

interface

Shows the trust status and inspection rate limit for

ports

show ip arp inspection log

Shows information about entries stored in the log,

including the associated VLAN, port, and address

components

Summary of Contents for iPECS ES-4526G

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS ES-4526G

Reviews:

Related manuals for iPECS ES-4526G

Brands by name

Popular brands

LG-Ericsson iPECS ES-4526G, User Manual

Search results

Summary of Contents for iPECS ES-4526G

Reviews:

Related manuals for iPECS ES-4526G

Brands by name

Popular brands