LG-Ericsson iPECS ES-4526G User Manual Download Page 231

Page: 231 / 1328

– 231 –

ES-4500G Series

TORM

ONTROL

ONFIGURATION

Use the Traffic > Storm Control page to configure broadcast, multicast, and

unknown unicast storm control thresholds. Traffic storms may occur when

a device on your network is malfunctioning, or if application programs are

not well designed or properly configured. If there is too much traffic on

your network, performance can be severely degraded or everything can
come to complete halt.

You can protect your network from traffic storms by setting a threshold for

broadcast, multicast or unknown unicast traffic. Any packets exceeding the

specified threshold will then be dropped.

CLI R

EFERENCES

◆

"switchport packet-rate" on page 844

OMMAND

SAGE

◆

Broadcast Storm Control is enabled by default.

◆

Broadcast control does not effect IP multicast traffic.

◆

When traffic exceeds the threshold specified for broadcast and

multicast or unknown unicast traffic, packets exceeding the threshold

are dropped until the rate falls back down beneath the threshold.

◆

The rate limits set by this function are also used by automatic storm

control when the control response is set to rate limiting by the

auto-

traffic-control action

command.

◆

Using both rate limiting and storm control on the same interface may

lead to unexpected results. For example, suppose broadcast storm

control is set to 500 pps by the command “switchport broadcast

packet-rate 500" and the rate limit is set to 200 Mbps by the command

“rate-limit input 20" on a port. Since 200 Mbps is 1/5 of line speed

(1000 Mbps), the received rate will actually be 100 pps, or 1/5 of the

500 pps limit set by the storm control command. It is therefore not

advisable to use both of these commands on the same interface.

ARAMETERS

These parameters are displayed in the web interface:

◆

Interface

– Displays a list of ports or trunks.

◆

Type

– Indicates interface type. (1000Base-T, SFP, or 10G)

◆

Unknown Unicast

– Specifies storm control for unknown unicast

traffic.

Summary of Contents for iPECS ES-4526G

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS ES-4526G

Reviews:

Related manuals for iPECS ES-4526G

Brands by name

Popular brands

LG-Ericsson iPECS ES-4526G, User Manual

Search results

Summary of Contents for iPECS ES-4526G

Reviews:

Related manuals for iPECS ES-4526G

Brands by name

Popular brands