LG-Ericsson iPECS ES-4526G User Manual Download Page 208

Page: 208 / 1328

HAPTER

| Spanning Tree Algorithm

Configuring Loopback Detection

– 208 –

ES-4500G Series

ONFIGURING

OOPBACK

ETECTION

Use the Spanning Tree > Loopback Detection page to configure loopback

detection on an interface. When loopback detection is enabled and a port

or trunk receives it’s own BPDU, the detection agent drops the loopback

BPDU, sends an SNMP trap, and places the interface in discarding mode.

This loopback state can be released manually or automatically. If the

interface is configured for automatic loopback release, then the port will

only be returned to the forwarding state if one of the following conditions is

satisfied:

◆

The interface receives any other BPDU except for it’s own, or;

◆

The interfaces’s link status changes to link down and then link up again,

or;

◆

The interface ceases to receive it’s own BPDUs in a forward delay

interval.

OTE

If loopback detection is not enabled and an interface receives it's

own BPDU, then the interface will drop the loopback BPDU according to

IEEE Standard 802.1w-2001 9.3.4 (Note 1).

OTE

Loopback detection will not be active if Spanning Tree is disabled on

the switch.

OTE

When configured for manual release mode, then a link down/up

event will not release the port from the discarding state.

CLI R

EFERENCES

◆

"Editing VLAN Groups" on page 922

ARAMETERS

These parameters are displayed in the web interface:

◆

Interface

– Displays a list of ports or trunks.

◆

Status

– Enables loopback detection on this interface.

(Default: Enabled)

◆

Trap

– Enables SNMP trap notification for loopback events on this

interface. (Default: Disabled)

◆

Release Mode

– Configures the interface for automatic or manual

loopback release. (Default: Auto)

◆

Release

– Allows an interface to be manually released from discard

mode. This is only available if the interface is configured for manual

release mode.

Summary of Contents for iPECS ES-4526G

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS ES-4526G

Reviews:

Related manuals for iPECS ES-4526G

Brands by name

Popular brands

LG-Ericsson iPECS ES-4526G, User Manual

Search results

Summary of Contents for iPECS ES-4526G

Reviews:

Related manuals for iPECS ES-4526G

Brands by name

Popular brands