LG-Ericsson ES-2010G Installation Manual Download Page 24

Page: 24 / 59

– 24 –

ES-2010G / ES-2010GP

ETWORK

LANNING

NTRODUCTION

WITCHING

A network switch allows simultaneous transmission of multiple packets via

non-crossbar switching. This means that it can partition a network more

efficiently than bridges or routers. The switch has, therefore, been

recognized as one of the most important building blocks for today’s

networking technology.

When performance bottlenecks are caused by congestion at the network

access point (such as the network card for a high-volume file server), the

device experiencing congestion (server, power user, or hub) can be

attached directly to a switched port. And, by using full-duplex mode, the

bandwidth of the dedicated segment can be doubled to maximize

throughput.

When networks are based on repeater (hub) technology, the distance

between end stations is limited by a maximum hop count. However, a

switch turns the hop count back to zero. So subdividing the network into

smaller and more manageable segments, and linking them to the larger

network by means of a switch, removes this limitation.

A switch can be easily configured in any Ethernet, Fast Ethernet, or Gigabit

Ethernet network to significantly boost bandwidth while using conventional

cabling and network cards.

PPLICATION

XAMPLES

The switches are not only designed to segment your network, but also to

provide a wide range of options in setting up network connections. Some

typical applications are described below.

OLLAPSED

ACKBONE

The Gigabit Ethernet Switches are an excellent choice for mixed Ethernet,

Fast Ethernet, and Gigabit Ethernet installations where significant growth is

expected in the near future. In a basic stand-alone configuration, it can

provide direct full-duplex connections for up to 10 workstations or servers.

You can easily build on this basic configuration, adding direct full-duplex

connections to workstations or servers. When the time comes for further

expansion, just connect to another hub or switch using one of the Gigabit

Ethernet ports built into the front panel, or a Gigabit Ethernet port on a

plug-in SFP transceiver.

Summary of Contents for ES-2010G




























































Search results

Summary of Contents for ES-2010G

Reviews:

Related manuals for ES-2010G

Brands by name

Popular brands

LG-Ericsson ES-2010G, Installation Manual

Search results

Summary of Contents for ES-2010G

Reviews:

Related manuals for ES-2010G

Brands by name

Popular brands