Lexus GS300 User Manual Download Page 555

Page: 555 / 622

CHASSIS

534

– STEERING

Free play

Less than 30 mm (1.2 in.)

– TIRES AND WHEELS

Tire size

245/40R18 93Y or P245/40R18 93V

Tire inflation pressure
Recommended cold tire inflation pressure

Front 230 kPa (2.3 kgf/cm

or bar, 33 psi)

Rear 230 kPa (2.3 kgf/cm

or bar, 33 psi)

For sustained high speeds above 160 km/h (100 mph), in
countries where such speeds are permitted by law, add 60 kPa
(0.6 kgf/cm

or bar, 9 psi) to the front tires and rear tires, but

never exceed the maximum cold tire inflation pressure molded
on the tire sidewall.

Wheel size

18 x 8 JJ

Wheel nut torque

103 N·m (10.5 kgf·m, 76 ft·lbf.)

NOTE:
For complete information on tires (e.g. replacing tires or replacing wheels), see “Checking tire inflation pressure”
through “Aluminum wheel precautions” on page 539 through 561.

Summary of Contents for GS300















































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for GS300

Reviews:

Brands by name

Popular brands

Lexus GS300, User Manual

Search results

Summary of Contents for GS300

Reviews:

Brands by name

Popular brands