Lexus ES330 2005 Owner'S Manual Download Page 54

Page: 54 / 438

SWITCHES

HEADLIGHT DIMMER AND TURN

SIGNAL SWITCH

For high beam, push the lever forward. Pull it back for low
beam. For the headlight flasher, pull it further back.

A blue light in the instrument cluster indicates high beam or

headlight flasher is on.
The headlight flasher works even when the headlight switch is

off.

For signaling turns, move the lever up or down in the
conventional manner.

The ignition key must be in the “ON” position.
The turn signal is self

−

cancelling after a turn, but after a lane

change, you may have to cancel it by hand. You can also signal

a lane change by moving the turn signal lever partway and

holding it there.
If the green light in the instrument cluster flashes faster than

normal, it indicates that the front or rear turn signal bulb has

burned out. If this indicator light does not come on, the fuse

or the indicator light itself has probably failed.

Summary of Contents for ES330 2005























































































































































































































































































































































































































































Search results

Summary of Contents for ES330 2005

Reviews:

Related manuals for ES330 2005

Brands by name

Popular brands

Lexus ES330 2005, Owner'S Manual

Search results

Summary of Contents for ES330 2005

Reviews:

Related manuals for ES330 2005

Brands by name

Popular brands