Repair information
4-2
4447-20x
Go Back
Previous
Next
Disassembly
Flow chart
Disassembly flow chart
The disassembly flow chart shows the sequence of procedures when removing a certain part or assembly. The
table below identifies the number of screws and connectors that need to be removed along with the part or
assembly.
Note:
The arrows point away from parts that must be removed to access the part in question. If a part does not
have an arrow pointing towards it, then it can be removed without removing any other parts. Click the illustration
of the part or assembly you want to remove to go to its corresponding removal procedure.
Part/assembly
Description
Number of cable
connectors
Number of fasteners
ADF input tray
Not a FRU, no tool required
N/A
N/A
ADF pick assembly and
separation pad
Not a FRU, no tool required
N/A
N/A
ADF door
Not a FRU, no tool required
N/A
N/A
Ink tank door
A FRU, no tool required
N/A
N/A
Power supply
Not a FRU, no tool required
N/A
N/A
Duplex unit
Not a FRU, no tool required
N/A
N/A
Rear cover
A FRU, tool required
N/A
5 plastic screws
Wall rib housing
A FRU, tool required
N/A
2 plastic screws
Pick tires
A FRU, no tool required
N/A
N/A
Left cover
A FRU, tool required
N/A
1 plastic screw
Right cover
A FRU, tool required
N/A
1 plastic screw
PCBA metal frame
support
Not a FRU, top level
assembly part
N/A
6 plastic screws
ADF/scanner assembly
A FRU, tool required
For Pro5500
• 7 cable connectors
• 1 ground connector
• 2 plastic screws
• 1 metal screw
ADF assembly
A FRU, tool required
5 cable connectors
6 plastic screws
Control panel assembly
A FRU, tool required
2 cable connectors
5 plastic screws
Flatbed scanner
assembly
A FRU, tool required
N/A
N/A
Wireless card
A FRU, tool required
1 cable connector
2 plastic screws
Card reader
A FRU, tool required
• 1 cable connector
• I ground connector
2 plastic screws
System board
A FRU, tool required
34 cable connectors
4 plastic screws
Midframe cover
A FRU, tool required
• 3 cable connectors
• 1 ground connector
• 4 plastic screws
• 1 metal screw
Printhead carrier card
cover
Not a FRU, top level
assembly part
N/A
2 plastic screws
Front cover assembly
A FRU, tool required
N/A
3 plastic screws
Encoder strip
A FRU, no tool required
N/A
1 spring hook
Alignment sensor
A FRU, tool required
N/A
1 plastic screw
Printhead carrier card
A FRU, tool required
4 cable connectors
1 plastic screw
Tank receiver assembly
A FRU, tool required
4 cable connectors
2 plastic screws
Print engine assembly
A FRU, tool required
N/A
4 plastic screws
Tube clip
Not a FRU, top level
assembly part
N/A
N/A
Printhead carrier card
holder
Not a FRU, top level
assembly part
N/A
2 plastic screws
Inlet
A FRU, tool required
N/A
2 plastic screws
Printhead
A FRU, no tool required
N/A
N/A
Summary of Contents for Pro5500 Series
