Lexmark CX331 User Manual Download Page 19

Page: 19 / 204

Set up, install, and conﬁgure

Selecting a location for the printer

•

Leave enough room to open trays, covers, and doors and to install hardware options.

•

Set up the printer near an electrical outlet.

CAUTION—POTENTIAL INJURY:

To avoid the risk of ﬁre or electrical shock, connect the power cord

to an appropriately rated and properly grounded electrical outlet that is near the product and easily
accessible.

CAUTION—SHOCK HAZARD:

To avoid the risk of electrical shock, do not place or use this product

near water or wet locations.

•

Make sure that airﬂow in the room meets the latest revision of the ASHRAE 62 standard or the CEN Technical
Committee 156 standard.

•

Provide a ﬂat, sturdy, and stable surface.

•

Keep the printer:

–

Clean, dry, and free of dust

–

Away from stray staples and paper clips

–

Away from the direct airﬂow of air conditioners, heaters, or ventilators

–

Free from direct sunlight and humidity extremes

•

Observe the temperature range.

Operating temperature 10 to 32.2°C (50 to 90°F)

•

Allow the following recommended amount of space around the printer for proper ventilation:

Top

305 mm (12 in.)

Rear

102 mm (4 in.)

Right side 76 mm (3 in.)

Set up, install, and conﬁgure

Summary of Contents for CX331













































































































































































































Search results

Summary of Contents for CX331

Reviews:

Related manuals for CX331

Brands by name

Popular brands

Lexmark CX331, User Manual

Search results

Summary of Contents for CX331

Reviews:

Related manuals for CX331

Brands by name

Popular brands