Lexmark 7003-050 X340n Service Manual Download Page 15

Page: 15 / 162

1-2

Service Manual

7003-XXX

Supported operating systems

The Lexmark X340, X340n, and X342n MFPs are compatible with following operating systems:

•

Microsoft Windows 2000 Professional

•

Microsoft Windows 2000 Server

•

Microsoft Windows 2000 Advanced Server

•

Microsoft Windows 2000 Server running Terminal Services

•

Microsoft Windows 2000 Server running Terminal Services under Citrix

MetaFrame

1.8

•

Microsoft Windows 2000 Server running Terminal Services under Citrix MetaFrame XP 1.0

•

Microsoft Windows XP

•

Microsoft Windows Server 2003 Standard Edition

•

Microsoft Windows Server 2003 Enterprise Edition

•

Microsoft Windows Server 2003 running Terminal Server

•

Microsoft Windows Server 2003 running Terminal Server with Citrix MetaFrame XP 1.0

Note: Citrix MetaFrame applications are limited to printing only.

Connectivity and compatibility

Ethernet connectivity is provided by an internal USB 2.0 daughtercard.

Supported external network connections

•

Lexmark N4000e ethernet 10Base/100BaseTX

•

Lexmark N4050e wireless 802.11g

•

Lexmark wireless 802.11g print server

Fonts

Note: There is no font card support.

Attachments

Standard USB 2.0 interface

X340, X340n and X342n

Fax Modem

X340, X340n and X342n

10/100 Base - TX

X340n, and X342n

Fonts/options

PCL scalable

PCL bitmap

manuals4u.com

Summary of Contents for 7003-050 X340n



































































































































































Search results

Summary of Contents for 7003-050 X340n

Reviews:

Brands by name

Popular brands

Lexmark 7003-050 X340n, Service Manual

Search results

Summary of Contents for 7003-050 X340n

Reviews:

Brands by name

Popular brands