Lexmark 7003-050 X340n Service Manual Download Page 140

Page: 140 / 162

Preventive maintenance

6-1

7003-XXX

6. Preventive maintenance

Printer engine

The Lexmark X340, X340n and X342n printer engines do not require preventive maintenance.

Scanner

The ADF pick pad (40X2404/40X3499) should be replaced every 20,000 pages, and the ADF pick roller
(40X2401) should be replaced every 60,000 pages.

Clean the flatbed glass using a lint free cloth. If the dirt is heavy, use a neutral cleanser or alcohol. Wipe the
glass carefully so no cleanser remains.

If the ADF is multi feeding, check the ADF pick roller and pad for dirt. Remove these parts and clean them with a
lint free cloth.

manuals4u.com

Summary of Contents for 7003-050 X340n



































































































































































Search results

Summary of Contents for 7003-050 X340n

Reviews:

Related manuals for 7003-050 X340n

Brands by name

Popular brands

Lexmark 7003-050 X340n, Service Manual

Search results

Summary of Contents for 7003-050 X340n

Reviews:

Related manuals for 7003-050 X340n

Brands by name

Popular brands