Lexmark 4500-00 Series Service Manual Download Page 147

Page: 147 / 246

Diagnostic aids

3-11

4500–E320/E322

Special function menu

The special function menu lets the following functions be executed
from the operator panel:

•

Execute engine cleaning cycle

•

Reset defaults

•

Enter configuration mode

•

Enter hex trace

•

Print diagnostics/print quality test page

•

Set demo mode active/inactive

Entering special function menu

1. Turn the printer off.

2. Open the printer cover.

3. Turn the printer on.

4. When the cover open error is indicated on the operator panel,

(Error light on), double press the button.

5. When the Error and Press Button lights start flashing, close the

cover.

The special function menu is now active.

Summary of Contents for 4500-00 Series























































































































































































































































Search results

Summary of Contents for 4500-00 Series

Reviews:

Related manuals for 4500-00 Series

Brands by name

Popular brands

Lexmark 4500-00 Series, Service Manual

Search results

Summary of Contents for 4500-00 Series

Reviews:

Related manuals for 4500-00 Series

Brands by name

Popular brands