Lexmark 4500-00 Series Service Manual Download

Page: 102 / 246

2-72

Service Manual

4500

Engine board service check (E320/E322)

FRU

Action

Engine board

24 V dc from the LVPS
board to the engine board.

1. Turn off printer.
2. Disconnect the fuser lamp cable

plug from the LVPS board. See

“Connector locations ” on
page 5-1

for more information.

3. Disconnect the LVPS/engine

board jumper cable from the
engine board. See

“Connector

locations ” on page 5-1

for more

information.

4. Turn printer on.

• If voltage is correct, ensure

J12–power supply unit (PSU) is
properly seated in the J12–PSU
connector on the engine board.

• Check for +24 V dc on the cable.
• If voltages are not present or

incorrect, see the

“Low voltage

power supply (LVPS) service
check ” on page 2-76

for more

information.

Note:

With all cables connected, the

printer should complete
POST within approximately
12–15 seconds in the
following sequence:

Summary of Contents for 4500-00 Series























































































































































































































































Search results

Summary of Contents for 4500-00 Series

Reviews:

Related manuals for 4500-00 Series

Brands by name

Popular brands

Lexmark 4500-00 Series, Service Manual

Search results

Summary of Contents for 4500-00 Series

Reviews:

Related manuals for 4500-00 Series

Brands by name

Popular brands