GreenMax
®
Distributed Room Controller
Cat. No. DRC00-0L0
INSTALLATION INSTRUCTIONS
ENGLISH
DI-001-DRC00-02A
WARNINGS
•
TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR
FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
• If you are unsure about any part of these instructions, consult an electrician.
CAUTIONS
• Use this device with
copper or copper clad wire only.
• For indoor applications only.
• Save these instructions.
The GreenMax Distributed Room Controller (DRC) comes in a Line Voltage and
Low Voltage LumaCAN™ powered product. The product manages all the energy
PDQDJHPHQWEXVLQHVVORJLFZLWKLQDVLQJOHURRPDQGLVIXOO\VHWXSDQGFRQ¿JXUHGXVLQJ
a Wi-Fi
®
enabled cell phone or tablet.
• Only one room controller should be used per room. Each room requires one controller.
• The LumaCAN network can span multiple rooms and connect multiple DRC devices
together; however it is important to pay particular attention to control and setup of rooms
to avoid cross room control.
• Each GreenMax DRC Controller can connect to a variety of devices, such as DRC smart
SDFNVUHOD\SDQHOV,QWHOOHFW¿[WXUHV/XPLQD5)VHQVRUV'$/,GHYLFHVDQGRWKHU
GHYLFHV)RUVSHFL¿FFDSDELOLWLHVDQGFDSDFLWLHVUHIHUWRWKHSURGXFWGDWDVKHHW
Application Notes
WARNING
:
TO AVOID FIRE, SHOCK, OR DEATH;
TURN OFF POWER at circuit breaker or fuse and test
that power is off before wiring!
1.
Mount the controller using one of the mounting options.
NOTE:
To remove the controller from the DIN rail, pull
down on the tension spring and lift off.
Installation
a.
Mounting on DIN rail
To remove
from DIN rail
DIN rail
mounting ears
b.
Mounting with mounting ears
Low Voltage Input
1. Pinout:
Pin 1 - Signal Input
Pin 2 - Common
Pin 3 - +24 VDC
(V follows LumaCAN supply)
2. Detects 0-24VDC. Can be used as contact
closure, 0-10V photocell input, or dry contact.
2.
Make all low voltage connections per the wiring diagram.
&RQ¿JXUDWLRQ
1.
&RQ¿JXULQJWKHFRQWUROOHU
,QRUGHUWRFRQ¿JXUHDURRPZLWKWKH*UHHQ0D['5&LWLVQHFHVVDU\WRKDYHDQL26RU$QGURLG:L)LFDSDEOHGHYLFHZLWKWKH³*UHHQ0D['5&´$SSLQVWDOOHG&RQQHFWWRWKH*UHHQ0D[
'5&&RQWUROOHUDVD:L)L$FFHVVSRLQWWKHQXVHWKH$SSWRPRYHWKURXJKWKHFRQ¿JXUDWLRQSURFHVV
• Factory Default Access Point Name: GreenMax DRC-[serial number] (The serial number is printed on the product label, use
only
last four character.)
• Factory Default Security: WEP Security, Password: leviton0000
2.
&KDQJLQJQHWZRUNFRQ¿JXUDWLRQ
,QVLWXDWLRQVZKHUHDZLUHOHVVDFFHVVSRLQWRUSDVVZRUGLVFKDQJHGEXWWKHFRQ¿JXUDWLRQRIWKH'5&QHHGVWRUHPDLQWKHVDPHXVHWKHIROORZLQJSURFHGXUHWRUHVHWWKHQHWZRUNDQG
reconnect to the device:
3UHVVDQGKROGWKH:L)LEXWWRQIRUVHFRQGVXQWLOWKH:L)L/('ÀDVKHVJUHHQUDSLGO\
• Release the button.
7KH/('ZLOOFRQWLQXHWRÀDVKJUHHQUDSLGO\XQWLOWKHUHVHWF\FOHLVFRPSOHWH7KH/('ZLOOJRGDUNWKHQEOLQNVORZO\LQGLFDWLQJWKDWLWLVUHDG\IRUFRQQHFWLRQXVLQJLWVIDFWRU\GHIDXOW
AP name and credentials.
NOTE:
WKDWHYHQWKRXJK\RXFDQFRQQHFWWRLW\RXPXVWKDYHEHHQJUDQWHGDFFHVVE\WKHVLWHDGPLQLVWUDWRUWRXVHWKHDSSIRUFRQ¿JXUDWLRQ
3.
LumaCAN
• Wire per the TIA-568B standard.
•
The sequence of network nodes, as described in the Construction Documents,
may be critical to ensure power distribution between nodes.
•
All LumaCAN wire segments must be tested and validated prior to powering up of the system.
•
The last device in each LumaCAN run must be terminated using an RJ45 terminator plug.
Each DRC is supplied with one terminator plug preinstalled in the smart pack.
•
Devices on LumaCAN follow daisy chain topology. Home Run topology supported with the
use of repeaters. Max 110 nodes per segment, max 250 nodes per sub-net.
• Perform voltage drop calculations on all networks.
To next device
From previous device
DI-001-DRC00-02A
© 2018 Leviton Mfg. Co., Inc.
WEB
VERSION
