SpecificationS
inputs
Gold Plated RCA jacks with adjustable gain
input impedance
50k Ohms
outputs
5 way gold plated binding posts
RMS continuous
50 Watts (40 Watts per channel 20Hz to 20kHz
output power
@ <0.2% THD all channels driven into 8 ohms)
Recommended
6 - 8 Ohms nominal
speaker impedance
frequency response
10 Hz - 40 kHz +/- 1dB (1W)
S/n ratio
over 105 dB A weighted (50 Watts)
tHD distortion
less than 0.1% 20 Hz to 20 kHz
iMD distortion
less than 0.01% 60 Hz 7 kHz 4:1 (SMPTE)
trigger control
12 VDC 35mA on 3.5mm mono jack
Dimensions
17" x 3.5" x 11.5" (432 x 89 x 292mm)
fan noise
quiet 28 dBA
power
750 Watts at 117 VAC or 230VAC
Weight
22 lbs (10 kg)
featuReS
• automatic protection circuitry –
Each amplifier channel is individually and fully protected against low impedance, overheating, overloading, over
voltage and under voltage. The protection circuitry automatically restores the sound once the affected amplifier channel returns to the safe operating
area.
•
individual input gain adjustment –
Each channel features an input gain adjustment to adjust the channel for volume, gain, and speaker sensitivity
variations.
• external power on/off –
The amplifier can be turned off and on by external controllers. To activate external power “on”, apply a 12VDC current to the
trigger jack using a compatible power supply. As long as the 12VDC is applied, the amplifier will remain on. The amplifier power switch should be in the
“off” position for external power control.
•
Link feature –
The Link button is normally set to the “in” position to give all six stereo inputs individual sources. When the Link button is set to the
“out” position, that input Left/Right is internally linked or cascaded to the source connected to input #1. Any of the five inputs (2 through 6) can be linked
individually in any combination to the #1 input. When all inputs are linked to input #1 the input impedance is about 8500 Ohms.
note:
When linked, unused RCA inputs can be used as outputs to other amplifiers.
• cooling fan –
The AE6MA features a thermostatically controlled internal fan to help to avoid overheating and keeping all channels within the safe
operating area so that the likelihood of the protection circuitry being activated is reduced. The fan also helps maximize energy efficiency.
inStaLLation
WaRninG:
TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES AND REGULATIONS.
WaRninG:
IF YOU ARE NOT SURE ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT A QUALIFIED ELECTRICIAN.
caution:
Never listen to sound that is distorted. If distorted sound is heard, turn the volume down immediately or speaker and/or amplifier damage
could occur that is not covered by the warranty.
caution:
The AE6MA contains no user serviceable parts. Do not attempt to open or repair the AE6MA.
user adjustments and Service:
There are no user adjustments on the AE6MA. Your installer may make certain gain level adjustments on the rear panel.
1.
The most important consideration when installing the AE6MA is cooling, since the amplifier packs a lot of audio power into a small-sized chassis. When
installing the amplifier in an equipment stack, it should be the top component. Make sure to leave at least 3-5 inches (76.19mm-127mm) of space above
the amplifier to allow for adequate cooling.
2.
Never operate the AE6MA on its side, as it will impair the unit’s cooling and void the warranty.
3.
Connect the AE6MA RCA inputs to the source component outputs using good quality RCA cables. Connect each channel individually, unless using the
Link feature.
4.
Connect the AE6MA speaker outputs to speakers using good quality speaker wire. It is recommended that 18 AWG speaker wire be used for runs up
to 50 feet (15 m). For runs from 50-150 feet (15-45 m), 16AWG speaker wire should be used. And for runs over 150 feet (45 m), 14 AWG speaker wire
should be used. Make sure the wire used is correctly rated for installation inside walls, ceilings, or floors. Check local codes for complete information.
12 channel (6 stereo pairs)
power amplifier
50 Watts RMS per Channel
Cat. No. AE6MA
installation instructions
LiMiteD 2 YeaR WaRRantY anD eXcLuSionS
Leviton warrants to the original consumer purchaser and not for
the benefit of anyone else that this product at the time of its
sale by Leviton is free of defects in materials and workmanship
under normal and proper use for two years from the purchase
date. Leviton’s only obligation is to correct such defects by repair
or replacement, at its option, if within such two year period the
product is returned prepaid, with proof of purchase date, and
a description of the problem to
Leviton Manufacturing co.,
inc., att: Quality assurance Department, 59-25 Little neck
parkway, Little neck, new York 11362-2591.
This warranty
excludes and there is disclaimed liability for labor for removal
of this product or reinstallation. This warranty is void if this
product is installed improperly or in an improper environment,
overloaded, misused, opened, abused, or altered in any manner,
or is not used under normal operating conditions or not in
accordance with any labels or instructions.
there are no other
or implied warranties of any kind, including merchantability
and fitness for a particular purpose
, but if any implied
warranty is required by the applicable jurisdiction, the duration of
any such implied warranty, including merchantability and fitness
for a particular purpose, is limited to two years.
Leviton is not
liable for incidental, indirect, special, or consequential
damages, including without limitation, damage to, or
loss of use of, any equipment, lost sales or profits or
delay or failure to perform this warranty obligation
. The
remedies provided herein are the exclusive remedies under
this warranty, whether based on contract, tort or otherwise.
for technical assistance call:
1-800-824-3005 (u.S.a. only)
www.Leviton.com
DI-000-AE6MA-00B
DI-000-AE6MA-00B
Outputs
Outputs
Outputs
AC120V
8 amps
NOTES:
Inputs use RCA connectors
Outputs use speaker binding posts
Inputs
Gain
Link-Out
1R
1L
L
R
1
2
2L 2R
1L+
1R+
1L–
1R–
2L–
2R–
2L+
2R+
3L+
3R+
3L–
3R–
4L–
4R–
4L+
4R+
5L+
5R+
5L–
5R–
6L–
6R–
6L+
6R+
Inputs
Gain
Link-Out
3R
3L
L
R
3
4
4L 4R
Link-Out
Link (out position)
cascades channel 1
to channels 2-6
Inputs
Gain
Link-Out
12V trigger
5R
5L
L
R
5
6
6L 6R
Link-Out
