manualshive.com logo in svg

Leuze electronic LSIS 222, Technical Description, Page: 78 / 95

Share
Download
Leuze electronic LSIS 222 Technical Description Download Page 78

Configuration using online commands

#

Technical description LSIS 22x

Leuze electronic

8

Configuration using online commands

Configuration can be performed via the RS 232 interface or via the USB interface with COM
port emulation with online commands.

Examples for online commands

Example 1

:

To, e.g., configure a <STX> as prefix, the following command string must be sent: 

<SYN>M<CR>PREBK29902.

The response from the LSIS 22x is: 

PREBK29902<ACK>.

If an 

<ENQ>

 is sent as response, the command syntax was incorrect.

If an 

<NAK>

 is sent, the command could not be executed because the permissible value/

range was exceeded.

Notice!

If no response is received to the sent command, the interface is probably not correctly set.

Example 2

:

To deactivate Code 128 as a readable code, the following command string must be sent: 

<SYN>M<CR>128ENA0.

The response from the LSIS 22x is: 

128ENA0<ACK>.

Notice!

The commands correspond to the content of the configuration codes that are printed in this
technical description. For further information on the topic of online commands, please con-
tact Leuze electronic.

Summary of Contents for LSIS 222
































































































Reviews:

No comments