manualshive.com logo in svg

Leuze electronic LSIS 222, Technical Description, Page: 77 / 95

Share
Download
Leuze electronic LSIS 222 Technical Description Download Page 77

Configuration using configuration codes

Leuze electronic

Technical description LSIS 22x

75

TNT

 35/7-2

4

V

7.6.4

Reset to factory settings

By reading in the following service code, the LSIS 22x is reset to factory settings.

Attention!

When resetting to factory settings, the entire configuration of the LSIS 22x is lost and
all parameters are reset to their standard values. 

Figure 7.50: Service code for resetting to factory settings

Listed in the following are the most important factory settings according to device model:

Factory settings LSIS 222 M5M-R1 - RS 232 interface

• Baud  rate

9600bit/s

• Data format

8

 data bits, 

no

 parity, 

1

 stop bit

• Framing

<STX>

DATA

<CR><LF>

• No read character

’

?

’

• Manual trigger mode

start command: 

<SYN>T<CR>

stop command: 

<SYN>U<CR>

Factory settings LSIS 223 M5M-R1 - USB interface

• USB  operating  mode

USB keyboard emulation

• Keyboard layout 

GERMAN

• Framing

’

ENTER

’

• No read character

none

• Streaming  presentation mode

Reset to factory settings

Summary of Contents for LSIS 222
































































































Reviews:

No comments