manualshive.com logo in svg

Leuze electronic LSIS 222, Technical Description, Page: 40 / 95

Share
Download
Leuze electronic LSIS 222 Technical Description Download Page 40

Configuration using configuration codes

38

Technical description LSIS 22x

Leuze electronic

7.2.3

Streaming presentation mode

By reading in one of the following configuration codes, 

streaming presentation mode

 is

set to either the 

normal

 or 

enhanced

 variant.

Figure 7.11: Configuration codes for setting the streaming presentation mode

Attention!

If a trigger occurs by means of a button or trigger input while the LSIS 22x is in
presentation mode, the LSIS 22x switches to manual/serial trigger mode!

Each time the trigger button is pressed or trigger input is activated, the LSIS 22x is again
activated as long as the trigger button is pressed or a high-signal is applied at the trigger
input.

If no trigger is initiated via the button or the switching input for the duration of the 

hands

free time-out

 

time (factory setting: 5s), the LSIS 22x returns to presentation mode.

In manual/serial trigger mode, the 

hands free time-out

 time is not active.

See "Configuring the hands free time-out time" on page 37. 

Streaming presentation mode - normal

Streaming presentation mode - enhanced

Summary of Contents for LSIS 222
































































































Reviews:

No comments