Leuze electronic LSIS 222 Technical Description Download Page 28

Page: 28 / 95

Electrical connection

Technical description LSIS 22x

Leuze electronic

5.2.2

LSIS 223 M5M-R1 - USB interface

The USB interface is used primarily for outputting the read and decoded code contents of
the activated code types.

Notice!

Preferably, use the ready-made connection cables from Leuze electronic (see chapter 10.3
on page 78).

Attention!

Observe the maximum cable length of 3m!

If using self-made cables, observe the following notice:

Notice for connecting the USB interface!

Ensure adequate shielding. The entire connection cable must be shielded and earthed. Use
only full-/high-speed data lines acc. to USB 2.0 specifications.

USB cable assignments

Figure 5.6:

USB pin assignment

SWI

SWO

n. c.

D+ Data

D- Data

GND

Host

3
2

GND

D+
D-

rt/RD

ws/WH

gn/GN

sw/BK

up to 3m!

shield

Summary of Contents for LSIS 222
































































































Search results

Summary of Contents for LSIS 222

Reviews:

Leuze electronic LSIS 222, Technical Description, Page: 28 / 95

Search results

Summary of Contents for LSIS 222

Reviews: