manualshive.com logo in svg

Leuze electronic LSIS 222, Technical Description, Page: 18 / 95

Share
Download
Leuze electronic LSIS 222 Technical Description Download Page 18

Installation and mounting

16

Technical description LSIS 22x

Leuze electronic

4

Installation and mounting

4.1

Storage, transportation

Attention!

When transporting or storing, package the device so that it is protected against collision and
humidity. Optimal protection is achieved when using the original packaging. Heed the
required environmental conditions specified in the technical data.

Unpacking

Check the packaging for any damage. If damage is found, notify the post office or ship-
ping agent as well as the supplier.

Check the delivery contents using your order and the delivery papers:

• Delivered quantity
• Device type and model as indicated on the name plate
• Package  insert

The name plate provides information as to what LSIS type your device is. For specific infor-
mation, please refer to chapter 10.

Name plates of the code readers of the LSIS 22x series

Figure 4.1:

Device name plate LSIS 22x

Save the original packaging for later storage or shipping.

If you have any questions concerning your shipment, please contact your supplier or your
local Leuze electronic sales office.

Observe the applicable local regulations when disposing of the packaging materials.

Summary of Contents for LSIS 222
































































































Reviews:

No comments