Leuze electronic 50038948 Original Operating Instructions Download Page 28

Page: 28 / 74

Accessories/order codes

BCL 8

Leuze electronic

5.3

Connection unit MA 8-01

The modular connection unit is an optional accessory when connecting a BCL 8 to an

RS 485 interface. The RS 485 interface, the switching input and the switching output are all

connected to the MA 8-01. It also supplies voltage to the BCL 8. The MA 8-01 connection

unit offers the following advantages over the installation of the BCL 8 as a stand-alone

device:

• M12 socket for switching input and switching output
• M12 connector for RS 485 interface and voltage supply 24VDC
• M12 socket for connection of the BCL 8

Figure 5.2: Pin assignment - MA 8

PWR IN HOST/RS485

= Voltage supply/RS 485 host interface

SW IN/OUT

= Switching input/output

BPS

= Connection to BCL 8/BPS 8

Note!
The SW IN/OUT connection is sealed with a thread plug upon delivery.

all dimensions in mm

RXD

VIN

GND

SWIN/SWOUT

TXD

SWIN

VOUT

GND

SWOUT

A (P)

GND

VIN

B (N)

BPS

SW IN/OUT

PWR IN

HOST/RS485

M12 socket

(A-coded)

M12 socket

(A-coded)

M12 connector

(A-coded)

ATTENTION!

Degree of protection IP 67 is achieved only if the connectors and caps are screwed into

place!

UM_BCL8_de_50040581.book Seite 26 Montag, 24. Februar 2020 9:53 09

Summary of Contents for 50038948











































































Search results

Summary of Contents for 50038948

Reviews:

Brands by name

Popular brands

Leuze electronic 50038948, Original Operating Instructions

Search results

Summary of Contents for 50038948

Reviews:

Brands by name

Popular brands