manualshive.com logo in svg

Leuze electronic 50038948, Original Operating Instructions

Share
Download
Leuze electronic 50038948 Original Operating Instructions Download Page 27

Accessories/order codes

Leuze electronic

BCL 8

25

TN

T 3

5/7-

24V

5.2.4

MA 8.1 - BCL - connecting the BCL 8 to the MA 8.1

Figure 5.1: MA 8.1 - Pin assignment BCL

The BCL 8 is connected to the MA 8.1 via the connection cable KB 008-1000/2000/3000

(AA/AR). The voltage supply is connected via the PWR IN HOST/RS232 socket.

BCL (5-pin socket, A-coded)

Pin

Name

Comment

1

VIN

Supply voltage for BCL 8 

+4.9 … +5.4VDC

2

TXD RS 232 transmission line

3

GND Supply voltage: 0VDC

4

RXD RS 232 receiving line

5

SWIN/

SWOUT

Programmable switching input/output of the 

BCL 8

Thread

FE

Functional earth (housing)

1

2

3

4

5

RXD

VIN

GND

SWIN/SWOUT

TXD

BCL 8

M12 socket

 

ATTENTION!

Degree of protection IP 67 is achieved only if the connectors and caps are screwed into

place!

 

ATTENTION!

It is absolutely necessary to connect the functional earth, since all electrical interference

(EMC coupling) is discharged via the functional earth connection.

UM_BCL8_de_50040581.book  Seite 25  Montag, 24. Februar 2020  9:53 09

Summary of Contents for 50038948











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands