Leroy-Somer POWERDRIVE MD2CS Installation And Maintenance Manual Download Page 18

Page: 18 / 48

LEROY-SOMER

4946 - 2013.07 / a

POWERDRIVE MD2CS

InstallatIon and maIntenance

Chassis-mounted variable speed drive

connectIons

3 - CONNECTIONS

• All connections work must be performed by

qualified electricians in accordance with the laws in

force in the country in which the drive is installed. This

includes earthing to ensure that no directly accessible

part of the drive can be at the mains voltage or any other

voltage which may be dangerous.

• The drive must be supplied through an approved

circuit-breaking device so that it can be powered down

safely.

• The drive power supply must be protected against

overloads and short-circuits.

• Check that the voltage and current of the drive, the

motor and the mains supply are compatible.

• The voltages on the connections of the mains supply,

the motor, the braking resistor or the filter may cause

fatal electric shocks. •

Only one permanent magnet motor can be connected to

the drive output. It is recommended to install a circuit-

breaking device between the permanent magnet motor

and the drive output to eliminate the risk of hazardous

voltage feedback when performing maintenance work.

• See also the recommendations in section 7.

3.1 - Power connections

3.1.1 - Electronics and forced ventilation power

supply

the control electronics and forced ventilation units need to

be supplied through a single-phase external power source

(terminal on control bloc).

The neutral of the electronics power supply must

not be connected to earth

• Electrical characteristics:

Voltage

Maximum power

Electronics

power

supply

230 V

isolated

100 Va

Forced

ventilation

and

auxiliaries

power

supply

230 V

connected

to earth

60t to 150t:

P = 300 Va

180t to 270t:

P = 500 Va

340t to 470t:

P = 1200 Va

270tH to 500tH: P = 1200 Va

3.1.2 - Characteristics of connection terminals

Refs.

Functions/connections

Type of connection and tightening torque

60T to 150T

180T to 270T

340T to 470T

270TH to 500TH

L1, L2, L3

mains power supply

m8 bolt - 12 nm

m10 screw bolt - 20 nm

U, V, W

motor outputs

earth

m8 bolt - 12 nm

m8 bolts - 12 nm

P4, P5 (see §4.4)

emc commoning link

torx screws Ø20 - 4 nm

control block (1)

spring terminal block

DC +, DC -

optionnal braking

transistor

blot m10, 20nm

DC +, BR

P14 (see §5.5)

14 points He10 connector

SDR

Rectifier enable input

connector

Forced ventilations

spring terminal block

Do not exceed the indicated maximum tightening torque.

(1) the neutral of the electronics power supply must not be connected to earth

Summary of Contents for POWERDRIVE MD2CS

















































Search results

Summary of Contents for POWERDRIVE MD2CS

Reviews:

Leroy-Somer POWERDRIVE MD2CS, Installation And Maintenance Manual, Page: 18 / 48

Search results

Summary of Contents for POWERDRIVE MD2CS

Reviews: