Lenze PROFINET 9400 Communications Manual Download Page 38

Page: 38 / 119

Commissioning

6.4

Setting the IP configuration

Lenze · E94AYCER communication module (PROFINET®) · Communication Manual · DMS 11.0 EN · 04/2016 · TD17

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

6.4.1

Setting via the PROFINET configurator of the »Engineer«



How to set the IP parameters via the PROFINET configurator:

1. Execute the menu command

Online



PROFINET configurator / EtherNet/IP addresses ...

The "Assign IP addresses" dialog window is opened and all Lenze PROFINET nodes

connected are listed.



Note!

• The IP address must only be allocated manually in the »Engineer« if the PROFINET

network is not operated on the IO controller yet (IP address has not been allocated by

the IO controller yet).

• While setting the IP parameters in the »Engineer«, PROFINET communication with the

IO controller must not take place at the same time.

• Changes will be effective immediately and are saved with mains failure protection.
• The currently used parameter values are shown in codes

C13010

C14010

(IP

address),

(subnet mask), and

(gateway address).

Summary of Contents for PROFINET 9400
























































































































Search results

Summary of Contents for PROFINET 9400

Reviews:

Related manuals for PROFINET 9400

Brands by name

Popular brands

Lenze PROFINET 9400, Communications Manual

Search results

Summary of Contents for PROFINET 9400

Reviews:

Related manuals for PROFINET 9400

Brands by name

Popular brands