Lenze PROFINET 9400 Communications Manual Download Page 27

Page: 27 / 119

Lenze · E94AYCER communication module (PROFINET®) · Communication Manual · DMS 11.0 EN · 04/2016 · TD17

Installation

5.2

Electrical installation

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

5.2.3

PROFINET connection

PROFINET is connected via the RJ45 sockets

X241

and

X242

For connection of the communication module to the PROFINET fieldbus, a standard Ethernet patch

cable is suitable.



Ethernet cable specification

(



29)

The installation and removal of the Ethernet cables is optimised for the use of connectors in

accordance with the "Automation Initiative of German Domestic Automobile Manufacturers"

(AIDA).

Pin assignment



Tip!

The PROFINET interfaces feature an auto-MDIX function. This function adjusts the polarity

of the RJ45 interfaces so that a connection can be established irrespective of the polarity of

the opposite PROFINET interface and irrespective of the type of cable used (standard patch

cable or crossover cable).



Note!

To prevent the RJ45 socket from being damaged, insert or remove the Ethernet cable

connector straight (at a right angle) into or from the socket.

RJ45 socket

Pin

Signal

E94AYCXX004C

Tx +

Tx -

Rx +

Rx -



Note!

Dependent on the configuration of the Ethernet port of the device to be connected, we

recommend the use of a cross-over cable.

Summary of Contents for PROFINET 9400
























































































































Search results

Summary of Contents for PROFINET 9400

Reviews:

Related manuals for PROFINET 9400

Brands by name

Popular brands

Lenze PROFINET 9400, Communications Manual

Search results

Summary of Contents for PROFINET 9400

Reviews:

Related manuals for PROFINET 9400

Brands by name

Popular brands