Lenze POWERLINK E84DGDV Series Communications Manual Download Page 59

Page: 59 / 70

Lenze · Decentralised frequency inverter 8400 motec (POWERLINK Option) · EDS84DMOTPL EN 1.0 - 11/2018

Parameter reference

Parameters relevant for POWERLINK communication

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

C13910

C13915

C13920

Parameter | Name:

C13910 | Last Module Error

Data type: UNSIGNED_32

Index: 10665

= 29A9

Display of the error code of the error last occurred in the Communication Unit

Selection list

(Lenze setting printed in bold)

0 No error

297566817 Warning locked INVALID_ADDR

29122816 Software error
96239921 Fault OPER_LOST

230457649 Quick stop OPER_LOST
297566513 Warning locked OPER_LOST
431784241 Information OPER_LOST

96240229 Fault CN_SoC_LOSS

230457957 Quick stop CN_SoC_LOSS
297566821 Warning locked CN_SoC_LOSS
431784549 Information CN_SoC_LOSS

96240230 Fault COM_CRC

230457958 Quick stop COM_CRC
297566822 Warning locked COM_CRC
431784550 Information COM_CRC



Read access



Write access



CINH



PLC-STOP



No transfer



PDO_MAP_RX



PDO_MAP_TX



COM



MOT

Parameter | Name:

C13915 | CustomerObject[16]

Data type: OCTET_STRING

Index: 10660

= 29A4

The code contains an octet string[16] for customised use.

Setting range

(min. value | unit | max. value)

Subcodes

Lenze setting

Info

C13915/1

00000000000000000000000000000

000



Read access



Write access



CINH



PLC-STOP



No transfer



PDO_MAP_RX



PDO_MAP_TX



COM



MOT

Parameter | Name:

C13920 | Current address switch

Data type: UNSIGNED_8

Index: 10655

= 299F

The code displays the current DIP switch position (node ID).

Not all switch positions are useful. The values for node IDs assigned by means of switches are between 1 and 239.



Node address (node ID) setting (



26)

Display range

(min. value | unit | max. value)

255



Read access



Write access



CINH



PLC-STOP



No transfer



PDO_MAP_RX



PDO_MAP_TX



COM



MOT

Summary of Contents for POWERLINK E84DGDV Series







































































Search results

Summary of Contents for POWERLINK E84DGDV Series

Reviews:

Related manuals for POWERLINK E84DGDV Series

Brands by name

Popular brands

Lenze POWERLINK E84DGDV Series, Communications Manual

Search results

Summary of Contents for POWERLINK E84DGDV Series

Reviews:

Related manuals for POWERLINK E84DGDV Series

Brands by name

Popular brands