Lenze E94AYCEO Communications Manual Download Page 32

Page: 32 / 149

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

Installation

5.2

Electrical installation

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

5.2.5

External voltage supply

The communication module can be supplied externally with voltage via separate supply cables at

the 2-pole plug connector

X232

The external voltage supply of the communication module is necessary if the power supply for the

basic device fails but communication via the fieldbus is to be maintained.
The parameters of a standard device separated from the mains cannot be accessed.

Assignment of the X232 plug connector

Terminal data



Note!

With external voltage supply, always use a separate power supply unit, safely separated

to EN 61800-5-1 in every control cabinet (SELV/PELV).

Name

Description

U = 24 V DC (20.4 ... 28.8 V)

I = 130 mA

Reference potential for the external voltage supply

Range

Values

Electrical connection

2-pin plug connector with spring connection

Possible connections

Rigid:

1.5 mm

(AWG 16)

Flexible:

Without wire end ferrule

1.5 mm

(AWG 16)

With wire end ferrule, without plastic sleeve

1.5 mm

(AWG 16)

With wire end ferrule, with plastic sleeve

1.5 mm

(AWG 16)

Stripping length

9 mm

Summary of Contents for E94AYCEO






















































































































































Search results

Summary of Contents for E94AYCEO

Reviews:

Lenze E94AYCEO, Communications Manual, Page: 32 / 149

Search results

Summary of Contents for E94AYCEO

Reviews: