Lenze E94AYCEO Communications Manual Download Page 28

Page: 28 / 149

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

Installation

5.2

Electrical installation

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

5.2.3

EtherNet/IP connection

The EtherNet/IP connection is carried out via the RJ45 sockets

X233

and

X234

You can use a standard Ethernet patch cable to connect the communication module to the

EtherNet/IP fieldbus.



Ethernet cable specification

(



30)

The installation and removal of the Ethernet cables is optimised for the use of connectors in

accordance with the "Automation Initiative of German Domestic Automobile Manufacturers"

(AIDA).

Pin assignment



Tip!

The EtherNet/IP interfaces feature an auto-MDIX function. This function adjusts the

polarity of the RJ45 interfaces so that a connection can be established irrespective of the

polarity of the opposite EtherNet/IP interface and irrespective of the type of cable used

(standard patch cable or crossover cable).



Note!

To prevent the RJ45 socket from being damaged, insert or remove the Ethernet cable

connector straight (at a right angle) into or from the socket.

RJ45 socket

Pin

Signal

E94AYCXX004C

Tx +

Tx -

Rx +

Rx -



Note!

Dependent on the configuration of the Ethernet port of the device to be connected, we

recommend the use of a cross-over cable.

Summary of Contents for E94AYCEO






















































































































































Search results

Summary of Contents for E94AYCEO

Reviews:

Lenze E94AYCEO, Communications Manual, Page: 28 / 149

Search results

Summary of Contents for E94AYCEO

Reviews: