manualshive.com logo in svg

Lenze E94AYCEO, Communications Manual, Page: 17 / 149

Share
Download
Lenze E94AYCEO Communications Manual Download Page 17

4

Technical  data

4.2

Protocol data

17

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

 

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 

4.2

Protocol data

4.3

Communication time

The communication time is the time between the start of a request and the arrival of the

corresponding response.
The communication times in an EtherNet/IP network depend on the ...

• processing time in the inverter;
• telegram runtime (baud rate / telegram length);
• nesting depth of the network.

processing time within the inverter

There are no interdependencies between parameter data and I/O data.

Range

Values

I/O data words

1 ... 32 words (max. 64 bytes, 16 bits/word)

Supported CIP services

• Get_Attributes_All

• Get_Attribute_Single

• Set_Attribute_Single

• Reset (only type ’0’)

• Forward_Open

• Forward_Close

Data

Processing time

Process data (I/O data)

10 ms

+ 0 ... 1 ms

+ 1 ... x ms

Lenze standard update cycle (can be changed in the Rockwell 

engineering tool)

Processing time in the module

Runtime of the application task of the technology 

application used (tolerance)

Parameter data

Approx. 30 ms + a tolerance of 20 ms (typically)

Some codes may require a longer processing time (see reference manual/

»Engineer« online help for the Servo Drive 9400).

Summary of Contents for E94AYCEO






















































































































































Reviews:

No comments